B6 · Potential difference: energy per charge · Answer key

Download the printable PDF

Explain potential difference as energy per charge, use ΔE = qΔV, and use the electron volt.

Open the complete lesson

Method slides in this lesson: “Method: how to solve an energy-per-charge problem” · “Method: how to find the speed of a charge accelerated through a voltage”. Worked examples for each question type in B6

After the lesson: Investigate and connect (a short investigation, a data step and a real-world link)

Slide 1 of 7 · Work that stores energy between plates

Key ideas

A positive particle against the negative plate is where it wants to be, so we call its electric potential energy (written Ep) zero there, like a ball at the bottom of a hill.

To carry it toward the other plate something outside must push, because the plates pull and push it back. Our push does work.

The speed stays constant, so none of the work becomes kinetic energy. All the work is stored as electric potential energy: ΔEp = 6.0 × 10⁻¹⁶ J in the example, where Δ means “change in”. When released, Ep decreases and the same amount becomes kinetic energy, written Ek.

The positive plate pushes a positive charge away and the negative plate pulls it in.

Example

A positive particle with q = 4.0 × 10⁻¹⁷ C is carried at constant speed from the negative top plate (A) to B, gaining 6.0 × 10⁻¹⁶ J of electric potential energy. It is released from rest and gravity is too small to matter. Which way does it move, and how much kinetic energy does it have when it reaches the top plate?

  1. The positive plate repels the particle and the negative plate attracts it, so the force at B points up and the particle moves up toward the negative top plate.
  2. As it moves, electric potential energy turns into kinetic energy. With no other losses, all 6.0 × 10⁻¹⁶ J becomes kinetic energy at the top plate.

Try it

The same positive particle is held at B, with 6.0 × 10⁻¹⁶ J of electric potential energy, and is carried at constant speed back to the negative top plate at A. Does its electric potential energy increase or decrease, by how much, and what is its potential energy at A?

  1. The field pushes the positive particle toward the negative plate, so the field does positive work as it moves from B to A.
  2. The stored energy decreases by 6.0 × 10⁻¹⁶ J (ΔEp = −6.0 × 10⁻¹⁶ J).
  3. At A, Ep = 6.0 × 10⁻¹⁶ J − 6.0 × 10⁻¹⁶ J = 0, which is the zero point we chose.

Slide 2 of 7 · Potential difference: energy per charge

Key ideas

A bigger charge stores more energy, so divide out the charge. Electric potential difference is ΔV = ΔE ÷ q: ΔE is the energy change (J) and q is the size of the charge (C).

Its unit is J/C (joules per coulomb). ΔV belongs to the plates, not the particle: a charge three times as big stores three times the energy, and ΔE ÷ q gives the same ΔV.

Rearrange for the unknown: ΔE = qΔV. Put in the size of the charge, then ask which way it moves: moving toward the plate that attracts it means it gains kinetic energy. If the plates do not change, ΔV stays the same for a new charge.

On a graph of ΔE against q, ΔE = qΔV matches y = mx, so the slope is ΔV. The line passes through the origin, because zero charge stores zero energy. Check powers of ten, since the charges are very small.

Example

On other plates, a charge q = 6.0 × 10⁻¹⁸ C stores 1.8 × 10⁻¹⁶ J when moved from A to B. Find the potential difference between A and B, then find the energy stored when a charge of 1.5 × 10⁻¹⁷ C is moved between the same two points.

  1. ΔV = ΔE ÷ q = (1.8 × 10⁻¹⁶ J) ÷ (6.0 × 10⁻¹⁸ C) = 30 J/C.
  2. The plates are the same, so ΔV = 30 J/C. ΔE = qΔV = (1.5 × 10⁻¹⁷ C)(30 J/C) = 4.5 × 10⁻¹⁶ J.

Try it

The same plates move several charges from A to B, and the energy stored is graphed against the charge. The line passes through C = (2.0 × 10⁻¹⁸ C, 0.60 × 10⁻¹⁶ J) and D = (8.0 × 10⁻¹⁸ C, 2.40 × 10⁻¹⁶ J). What does the slope represent, and what is its value?

  1. Match ΔE = qΔV to y = mx. ΔE is vertical, q is horizontal, so the slope is the potential difference ΔV.
  2. Slope = (2.40 × 10⁻¹⁶ − 0.60 × 10⁻¹⁶) J ÷ (8.0 × 10⁻¹⁸ − 2.0 × 10⁻¹⁸) C = 1.8 × 10⁻¹⁶ ÷ (6.0 × 10⁻¹⁸) = 30 J/C.
  3. The line passes through the origin because zero charge stores zero energy.

Slide 3 of 7 · Method: how to solve an energy-per-charge problem

Key ideas

Step 1: name the unknown. Is it ΔE, q or ΔV? Write it before any number.

Step 2: write the equation with the unknown alone: ΔV = ΔE/q, ΔE = qΔV or q = ΔE/ΔV.

Step 3: put in the sizes: the size of the charge in coulombs and the energy in joules. Then ask which way it moves: toward the plate that attracts it, it gains kinetic energy.

Step 4: calculate with units. Joules per coulomb is the volt. Check: a bigger charge stores more energy.

Example

A charge of 6.0 × 10⁻¹⁸ C stores 1.8 × 10⁻¹⁶ J when it is moved from A to B. A charge of 1.5 × 10⁻¹⁷ C is then moved between the same two points. Find the potential difference, then the energy stored for the new charge.

  1. Steps 1 and 2: part one wants ΔV, so ΔV = ΔE ÷ q. Part two wants ΔE, so ΔE = qΔV.
  2. Step 3: ΔV = (1.8 × 10⁻¹⁶ J) ÷ (6.0 × 10⁻¹⁸ C). Then ΔE = (1.5 × 10⁻¹⁷ C) × ΔV, using the sizes of the charges.
  3. Step 4: ΔV = 30 J/C, so ΔE = (1.5 × 10⁻¹⁷)(30) = 4.5 × 10⁻¹⁶ J. The unit J/C is the volt, so ΔV = 30 V.

Try it

A charge of 2.5 × 10⁻¹⁷ C stores 1.0 × 10⁻¹⁵ J when it is moved between two plates. Find the potential difference between the plates, then the energy stored when a charge of 8.0 × 10⁻¹⁸ C is moved between the same plates.

  1. Steps 1 and 2: first ΔV = ΔE ÷ q, then ΔE = qΔV.
  2. Step 3: ΔV = (1.0 × 10⁻¹⁵ J) ÷ (2.5 × 10⁻¹⁷ C).
  3. Step 4: ΔV = 40 J/C. Then ΔE = (8.0 × 10⁻¹⁸ C)(40 J/C) = 3.2 × 10⁻¹⁶ J.
  4. Check: the smaller charge stores less energy than the first charge.

Slide 4 of 7 · The volt: one joule per coulomb

Key ideas

One volt is one joule per coulomb: 1 V = 1 J/C. “Voltage” is just potential difference. A battery label such as 9.0 V means ΔV = 9.0 V in an equation. Unlike the field E, ΔV has no direction.

A 9.0 V battery gives 9.0 J to each coulomb that passes through it. A battery does not store charge to hand out; it supplies energy for each coulomb already in the wires.

Pick the form that matches the unknown: energy from charge, ΔE = qΔV; charge from energy, q = ΔE ÷ ΔV. The unit V can always be swapped for J/C.

Example

A battery is labelled 9.0 V and is connected to a heating coil. A charge of 4.0 C flows through the coil. Find the energy delivered.

  1. ΔE = qΔV = (4.0 C)(9.0 V) = 36 J.
  2. That energy shows up as heat in the coil.

Try it

A 6.0 V battery is connected to a lamp. How much energy is delivered when 2.5 C of charge passes through the lamp, and how much charge must pass to deliver 90 J?

  1. ΔE = qΔV = (2.5 C)(6.0 V) = 15 J.
  2. q = ΔE ÷ ΔV = 90 J ÷ 6.0 V = 15 C.
  3. Check: 6.0 J per coulomb, so 90 J needs many coulombs.

Slide 5 of 7 · A charge accelerated through a voltage

Key ideas

Voltage supplies energy and the particle turns it into speed. Rearrange ΔV = ΔE/q to ΔE = qΔV. Kinetic energy is Ek = ½mv²; the small i means initial and f means final. Only the electric force changes the energy here, so all of qΔV becomes kinetic energy: qΔV = ½mv_f² − ½mv_i².

The initial term drops out only when the problem says “from rest” (v_i = 0). Do not drop it automatically.

From rest: v = √(2 × Ek ÷ m), where Ek = qΔV. If it is already moving, find the start energy ½mv_i² and the gain qΔV. Final Ek = start + gain, then solve for v.

Use the particle’s own q and m (electron, proton and alpha particle differ). Check: a particle sped up by the voltage must end faster than it started.

Example

An electron starts from rest at the negative plate of an electron gun and is accelerated through ΔV = 1.80 × 10³ V. With q = 1.60 × 10⁻¹⁹ C and m = 9.11 × 10⁻³¹ kg, find its speed at the positive plate.

  1. qΔV = (1.60 × 10⁻¹⁹ C)(1.80 × 10³ V) = 2.88 × 10⁻¹⁶ J.
  2. It starts from rest, so ½mv² = 2.88 × 10⁻¹⁶ J.
  3. v = √(2 × 2.88 × 10⁻¹⁶ ÷ (9.11 × 10⁻³¹)) = 2.51 × 10⁷ m/s.

Try it

An electron enters the gap at v_i = 1.50 × 10⁷ m/s and is accelerated through ΔV = 6.00 × 10² V. Find its final speed. Use q = 1.60 × 10⁻¹⁹ C and m = 9.11 × 10⁻³¹ kg.

  1. Initial energy: ½mv_i² = ½(9.11 × 10⁻³¹)(1.50 × 10⁷)² = 1.024 × 10⁻¹⁶ J.
  2. Energy gained: qΔV = (1.60 × 10⁻¹⁹)(6.00 × 10²) = 9.600 × 10⁻¹⁷ J.
  3. Final energy = 1.024 × 10⁻¹⁶ + 9.600 × 10⁻¹⁷ = 1.984 × 10⁻¹⁶ J.
  4. v_f = √(2 × 1.984 × 10⁻¹⁶ ÷ (9.11 × 10⁻³¹)) = 2.09 × 10⁷ m/s.
  5. Check: faster than 1.50 × 10⁷ m/s. (Treating it as starting from rest gives 1.45 × 10⁷ m/s, a typical wrong choice.)

Slide 6 of 7 · Method: how to find the speed of a charge accelerated through a voltage

Key ideas

Step 1: write the energy rule qΔV = ½mv_f² − ½mv_i². The energy gained from the voltage becomes kinetic energy.

Step 2: find the energy gained: qΔV, with the size of the charge in coulombs and the voltage in volts. The answer is in joules.

Step 3: find the starting energy. “From rest” means ½mv_i² = 0. If it is already moving, work out ½mv_i² with the particle’s own mass.

Step 4: final Ek = start + gain. Then v = √(2 × Ek ÷ m). Check: the unit is m/s, and a particle sped up by the voltage ends faster than it began.

Example

An electron starts from rest and crosses a gap with a voltage of 1.80 × 10³ V. With q = 1.60 × 10⁻¹⁹ C and m = 9.11 × 10⁻³¹ kg, find its speed at the end.

  1. Step 1: qΔV = ½mv_f² − ½mv_i².
  2. Step 2: qΔV = (1.60 × 10⁻¹⁹ C)(1.80 × 10³ V) = 2.88 × 10⁻¹⁶ J. Step 3: it starts from rest, so the starting energy is 0.
  3. Step 4: final Ek = 2.88 × 10⁻¹⁶ J. v = √(2 × 2.88 × 10⁻¹⁶ ÷ (9.11 × 10⁻³¹)) = 2.5145… × 10⁷ m/s, so v = 2.51 × 10⁷ m/s.

Try it

A proton starts from rest and is accelerated through 2.00 × 10³ V. With q = 1.60 × 10⁻¹⁹ C and m = 1.67 × 10⁻²⁷ kg, find its final speed.

  1. Step 1: qΔV = ½mv_f² − ½mv_i².
  2. Step 2: qΔV = (1.60 × 10⁻¹⁹ C)(2.00 × 10³ V) = 3.20 × 10⁻¹⁶ J. Step 3: from rest, so the starting energy is 0.
  3. Step 4: v = √(2 × 3.20 × 10⁻¹⁶ ÷ (1.67 × 10⁻²⁷)) = 6.1906… × 10⁵ m/s, so v = 6.19 × 10⁵ m/s.
  4. Check: the unit is m/s, and the proton has much more mass than an electron, so it ends slower than 2.51 × 10⁷ m/s.

Slide 7 of 7 · The electron volt

Key ideas

The electron volt (eV) is a unit of energy, not of voltage. One eV is the energy an electron gains when accelerated through one volt.

1 eV = qΔV = (1.60 × 10⁻¹⁹ C)(1 V) = 1.60 × 10⁻¹⁹ J (data sheet).

A charge of n electrons gains n eV for each volt: an electron through 24.0 V gains 24.0 eV, an alpha particle (charge 2e) through 15.0 V gains 30.0 eV.

To switch units: eV × 1.60 × 10⁻¹⁹ = joules, and joules ÷ (1.60 × 10⁻¹⁹) = eV. The equation ΔE = qΔV still needs joules, coulombs and volts. Read the unit in the question first and finish in it.

Example

An alpha particle (charge 3.20 × 10⁻¹⁹ C) is accelerated from rest through 45.0 V. Find the kinetic energy it gains, first in electron volts and then in joules.

  1. Its charge is 2e, so each volt gives it 2 eV: 2 × 45.0 V = 90.0 eV.
  2. In joules: 90.0 eV × 1.60 × 10⁻¹⁹ J/eV = 1.44 × 10⁻¹⁷ J.
  3. Check: qΔV = (3.20 × 10⁻¹⁹ C)(45.0 V) = 1.44 × 10⁻¹⁷ J. The two routes agree.

Try it

An electron enters the gap at 1.0 × 10⁶ m/s and is accelerated through 80.0 V. Find its final kinetic energy in electron volts. Record the answer as a.bc × 10ⁿ eV. Use m = 9.11 × 10⁻³¹ kg.

  1. Gain: an electron through 80.0 V gains 80.0 eV.
  2. Initial energy: ½mv² = ½(9.11 × 10⁻³¹ kg)(1.0 × 10⁶ m/s)² = 4.555 × 10⁻¹⁹ J, and 4.555 × 10⁻¹⁹ ÷ (1.60 × 10⁻¹⁹) = 2.847 eV.
  3. Final energy = 80.0 eV + 2.847 eV = 82.847 eV, which rounds to 82.8 eV.
  4. Record 8.28 × 10¹ eV. Round only at the end.

Answer the practice problems online · Completed notes and worked key

B6-N01

B6-N01. A charge of 5.0 × 10⁻¹⁸ C is moved between two points, and 1.5 × 10⁻¹⁶ J of energy is stored. Find the potential difference.

  1. Givens: q = 5.0 × 10⁻¹⁸ C; ΔE = 1.5 × 10⁻¹⁶ J. Question: ΔV.
  2. ΔV = ΔE ÷ q.
  3. ΔV = 1.5 × 10⁻¹⁶ ÷ (5.0 × 10⁻¹⁸) = 30.0 V.
  4. Answer: 30 V

B6-N02

B6-N02. A 12 V battery drives 8.0 C of charge through a motor. How much energy does the battery deliver, in joules?

  1. Givens: ΔV = 12 V; q = 8.0 C. Question: ΔE.
  2. ΔE = qΔV = (8.0)(12) = 96 J.
  3. Answer: 96 J

B6-N03

B6-N03. The potential difference between two points is 30 V. A second charge, twice as large, is moved between the same points. What is the new potential difference?

  1. 60 V, because the charge doubled
  2. 15 V, because q is in the denominator
  3. Zero, because the energy cancels
  4. 30 V, because ΔV belongs to the points and not to the charge
  1. Givens: ΔV = 30 V for the first charge; the charge doubles. Question: the new ΔV.
  2. The energy doubles, but ΔV = ΔE/q stays the same because both double.
  3. Answer: D. 30 V, because ΔV belongs to the points and not to the charge

B6-N04

B6-N04. An electron is accelerated from rest through 3500 V. Use e = 1.60 × 10⁻¹⁹ C and electron mass mₑ = 9.11 × 10⁻³¹ kg. Find its final speed.

  1. Givens: v₀ = 0; ΔV = 3500 V; q = 1.60 × 10⁻¹⁹ C; m = 9.11 × 10⁻³¹ kg. Question: v.
  2. qΔV = ½mv², so v = √(2qΔV/m).
  3. v = √(2(1.60 × 10⁻¹⁹)(3500) ÷ (9.11 × 10⁻³¹)) = 3.51 × 10⁷ m/s.
  4. This is well below the speed of light, so the formula ½mv² is reasonable.
  5. Answer: 3.51 × 10⁷ m/s

B6-N05

B6-N05. A particle with charge 4.80 × 10⁻¹⁹ C is accelerated from rest through 25.0 V. Find the kinetic energy it gains, in electron volts.

  1. Givens: q = 4.80 × 10⁻¹⁹ C = 3e; ΔV = 25.0 V. Question: the energy gained in eV.
  2. The charge is 3e, so it gains 3 eV for each volt.
  3. 3 × 25.0 = 75.0 eV.
  4. Answer: 75.0 eV

B6-N06

B6-N06. An electron enters a gap moving at 2.0 × 10⁷ m/s and is accelerated through 4.00 × 10² V. Find its final speed.

  1. Givens: v₀ = 2.0 × 10⁷ m/s; ΔV = 4.00 × 10² V; q = 1.60 × 10⁻¹⁹ C; m = 9.11 × 10⁻³¹ kg. Question: v.
  2. The electron already has kinetic energy: ½mv² = ½mv₀² + qΔV.
  3. v = √(v₀² + 2qΔV/m) = √(4.000 × 10¹⁴ + 1.405 × 10¹⁴) = 2.32 × 10⁷ m/s. Keep the full values on your calculator.
  4. The speed rises but is not more than the starting speed squared plus the gain, so it is reasonable. Do not add the speeds directly.
  5. Answer: 2.32 × 10⁷ m/s

B6-N07

B6-N07. An electron and a proton are each accelerated from rest through the same 100 V. Which gains more kinetic energy, and which ends with the greater speed? Explain.

  1. Givens: same ΔV = 100 V; equal size of charge e; masses 9.11 × 10⁻³¹ kg and 1.67 × 10⁻²⁷ kg. Question: compare energy and speed.
  2. Both gain the same energy, qΔV = 100 eV, because the charge magnitude and voltage are equal.
  3. From ½mv² = qΔV, v = √(2qΔV/m). The electron has the smaller mass, so it ends with the greater speed.