B5 · Reading straight-line graphs · Answer key

Download the printable PDF

Find a slope with its unit, match a graph to y = mx + b, and straighten a curve.

Open the complete lesson

Method slides in this lesson: “Method: how to get slope and constants from a graph” · “Method: how to straighten a curve”. Worked examples for each question type in B5

After the lesson: Investigate and connect (a short investigation, a data step and a real-world link)

Slide 1 of 8 · Two variables and a line of best fit

Key ideas

A fair test changes one thing and measures one thing. The manipulated variable is the one you change. The responding variable is the one you measure. Everything else is held fixed.

The manipulated variable goes on the horizontal axis. The responding variable goes on the vertical axis. Spring test: the stretch (m) is manipulated. The force (N) is responding.

Points never fall exactly on a line. Every reading has a small error. A line of best fit follows the trend.

Read values from the line, never from single data points. Choose two points on the line that are far apart, so the error is a small share of the answer.

Example

A student changes the source charge Q and measures the electric field strength E with a probe. The probe stays 0.500 m from the source in air. Which quantity is manipulated, which is responding, which is held fixed, and which one goes on the horizontal axis?

  1. Manipulated: source charge Q (horizontal axis). Responding: electric field strength E (vertical axis).
  2. Fixed: the distance r = 0.500 m, and the constant k, which is a fixed number of nature.
  3. If r also changed, E would depend on two things at once and the graph could not show how E depends on Q alone.

Try it

A student draws a line of best fit through six scattered points. To find the slope she reads two of the data points that are close together. Give two things she should change.

  1. Read the two points from the line of best fit, not from single data points, because each data point carries its own reading error and the line averages the errors out.
  2. Choose two points on the line that are far apart, so the same reading error is a small share of the rise and the run.

Slide 2 of 8 · Find the slope from the line

Key ideas

Slope = rise ÷ run. Rise is how far the line goes up. Run is how far it goes across. Take B minus A for both, in the same order. F_B is the force at B. x_A is the extension at A.

Slope = (y₂ − y₁) ÷ (x₂ − x₁). It shows how much the vertical quantity changes for each one unit of the horizontal quantity.

The slope unit is the vertical unit ÷ the horizontal unit. Here F is in N and x is in m, so the slope is in N/m. A slope without its unit is incomplete.

Convert the run to metres. Keep the power of ten. A slope of 250 or 0.25 instead of 25.0 N/m means the power of ten was lost.

Example

Points A (2.0 × 10⁻² m, 1.00 N) and B (10.0 × 10⁻² m, 3.00 N) lie on the line of best fit of spring force F against extension x. Find the slope.

  1. Rise = F_B − F_A (force at B minus force at A) = 3.00 N − 1.00 N = 2.00 N.
  2. Run = x_B − x_A = (10.0 − 2.0) × 10⁻² m = 8.0 × 10⁻² m = 0.080 m.
  3. Slope = 2.00 N ÷ 0.080 m = 25.0 N/m.

Try it

A different spring’s line of best fit passes through C = (3.0 × 10⁻² m, 1.40 N) and D = (9.0 × 10⁻² m, 3.80 N). Find the slope, including its unit. Show the rise, the run and the unit check.

  1. Rise = F_D − F_C = 3.80 N − 1.40 N = 2.40 N.
  2. Run = (9.0 − 3.0) × 10⁻² m = 6.0 × 10⁻² m = 0.060 m.
  3. Slope = 2.40 N ÷ 0.060 m = 40.0 N/m. Unit check: newtons per metre, vertical over horizontal.

Slide 3 of 8 · Match the physics equation to y = mx + b

Key ideas

A straight line follows y = mx + b. m is the slope. b is the vertical intercept, where the line crosses the vertical axis (x = 0). Hooke’s law is F = kx. F is the force (N). x is the extension (m). k is the spring constant (N/m).

Match the symbols one at a time. The vertical-axis quantity plays y. The horizontal-axis quantity plays x. The number multiplying x is the slope. The term that stands alone is the intercept.

In F = kx, F plays y and x plays x. So the slope is the spring constant k. The law has no b term, so a 0.50 N intercept is not part of the law.

Sometimes the intercept is real physics. In v = v₀ + at, a is the constant acceleration (m/s²) and v₀ is the starting speed (m/s). The term with no t is the initial speed v₀. Always ask if the physics equation has a b term.

Example

A cart’s speed v is plotted against time t, and the line of best fit has the equation v = v₀ + at, where a is a constant acceleration. Using y = mx + b, what does the slope represent and what does the vertical intercept represent?

  1. Match v to y and t to x. The number multiplying t is a, so the slope is the acceleration a (in m/s per s, which is m/s²).
  2. The term with no t is v₀, which plays the role of b, so the vertical intercept is the initial speed v₀.
  3. Here the intercept is real physics, not an error.

Try it

A graph of the electric field strength E against the source charge Q, measured at a fixed distance r from a point source, matches E = kQ/r². Using y = mx + b, what does the slope equal, and what should the intercept be?

  1. Match E to y and Q to x. The number multiplying Q is k/r², so the slope equals k/r² (r is fixed).
  2. The equation E = kQ/r² has no b term, so the ideal line passes through the origin and the intercept should be 0.

Slide 4 of 8 · Predict with the whole line, intercept included

Key ideas

Predict with the whole line: y = mx + b, intercept included. The spring line is F = (25.0 N/m)x + 0.50 N.

To find x from F, write the equation with F in it. Subtract the intercept first. Then divide by the slope. For F = 1.20 N: 0.70 = 25.0x, so x = 0.0280 m. F = kx alone gives 0.0480 m and leaves out the 0.50 N.

The line is in SI units, so convert first: 6.0 cm = 0.060 m. Forgetting to convert is a classic wrong choice.

Inside the measured range is interpolation. It is reliable. Past the range is extrapolation. It is less reliable, because the line may not stay straight.

Example

The spring line is F = (25.0 N/m)x + 0.50 N, from measured extensions up to 12 × 10⁻² m. The extension is 6.0 cm. Find the predicted force.

  1. Convert: 6.0 cm = 0.060 m.
  2. F = (25.0 N/m)(0.060 m) + 0.50 N = 1.50 N + 0.50 N = 2.00 N.
  3. Reading the graph at 6.0 × 10⁻² m gives the same 2.00 N.

Try it

The same line is F = (25.0 N/m)x + 0.50 N. A force of 2.30 N is applied. Find the extension this experiment predicts, in metres.

  1. 2.30 N = (25.0 N/m)x + 0.50 N.
  2. Subtract the intercept: 1.80 N = (25.0 N/m)x.
  3. x = 1.80 N ÷ 25.0 N/m = 0.072 m.
  4. Ignoring the intercept would give 0.092 m, which is too large by 0.020 m.

Slide 5 of 8 · Method: how to get slope and constants from a graph

Key ideas

Step 1: pick two points on the line. Use grid crossings, far apart. Use line points, not data points.

Step 2: slope = rise ÷ run. Keep the power of ten. The unit is the vertical unit ÷ the horizontal unit.

Step 3: match y = mx + b. Step 4: say what the slope and the intercept mean, with units. Does the physics equation have a b term?

Step 5: predict with the whole line. Check: the unit and the size fit the picture.

Example

The spring line is F = (25.0 N/m)x + 0.50 N. A and B lie on it at (2.0 × 10⁻² m, 1.00 N) and (10.0 × 10⁻² m, 3.00 N). Find the spring constant, then the extension for a force of 1.20 N. Write each step number beside your work.

  1. Step 1: A (2.0 × 10⁻² m, 1.00 N) and B (10.0 × 10⁻² m, 3.00 N), both on the line.
  2. Step 2: rise = 3.00 − 1.00 = 2.00 N. Run = (10.0 − 2.0) × 10⁻² m = 0.080 m. Slope = 2.00 ÷ 0.080 = 25.0 N/m.
  3. Steps 3 and 4: F plays y and x plays x, so 25.0 N/m is the spring constant. The intercept, 0.50 N, is not in Hooke’s law: it has no b.
  4. Step 5: 1.20 = 25.0x + 0.50, so 0.70 = 25.0x and x = 0.0280 m.

Try it

A line of best fit for another spring passes through (2.0 × 10⁻² m, 1.50 N) and (8.0 × 10⁻² m, 3.30 N). Find the slope and the intercept, then the force predicted for an extension of 5.0 cm. Write each step number beside your work.

  1. Step 2: rise = 3.30 − 1.50 = 1.80 N. Run = (8.0 − 2.0) × 10⁻² m = 0.060 m. Slope = 1.80 ÷ 0.060 = 30.0 N/m.
  2. Steps 3 and 4: F = 30.0x + b. Put in the first point: 1.50 = 30.0(0.020) + b, so b = 0.90 N.
  3. Step 5: 5.0 cm = 0.050 m. F = 30.0(0.050) + 0.90 = 1.50 + 0.90 = 2.40 N.

Slide 6 of 8 · Find Coulomb’s constant from a field graph

Key ideas

Here k is Coulomb’s constant, not a spring constant. E = kQ/r². E is the field strength (N/C). Q is the source charge (C). r is the distance (m). Q is manipulated (horizontal). E is responding (vertical). r and k are held fixed.

Match E = kQ/r² to y = mx. The slope is k/r². So k = slope × r². Multiply by r², do not divide.

Keep the powers of ten. Convert first: 1 μC = 1 × 10⁻⁶ C. Unit check: (N/C²)(m²) = N·m²/C².

Compare with the data-sheet 8.99 × 10⁹ N·m²/C². A numerical response uses three digits in the form a.bc × 10ⁿ.

Example

At r = 0.500 m, J = (2.0 μC, 1.0 × 10⁵ N/C) and K = (10.0 μC, 4.0 × 10⁵ N/C) lie on the line of E against Q. Find k from the graph. The data sheet gives 8.99 × 10⁹ N·m²/C².

  1. Rise = (4.0 − 1.0) × 10⁵ N/C = 3.0 × 10⁵ N/C. Run = (10.0 − 2.0) × 10⁻⁶ C = 8.0 × 10⁻⁶ C.
  2. Slope = 3.75 × 10¹⁰ N/C².
  3. k = slope × r² = (3.75 × 10¹⁰)(0.500)² = 9.38 × 10⁹ N·m²/C².
  4. Unit check: (N/C²)(m²) = N·m²/C². It differs from 8.99 × 10⁹ by about 4 %, close enough for a classroom experiment.

Try it

At r = 0.300 m, a line of best fit for E against Q passes through M = (3.0 × 10⁻⁶ C, 3.2 × 10⁵ N/C) and N = (9.0 × 10⁻⁶ C, 9.5 × 10⁵ N/C). Find the experimental value of Coulomb’s constant. Record it as a.bc × 10ⁿ N·m²/C².

  1. Rise = (9.5 − 3.2) × 10⁵ N/C = 6.3 × 10⁵ N/C. Run = (9.0 − 3.0) × 10⁻⁶ C = 6.0 × 10⁻⁶ C.
  2. Slope = 1.05 × 10¹¹ N/C².
  3. k = slope × r² = (1.05 × 10¹¹ N/C²)(0.300 m)² = 9.45 × 10⁹ N·m²/C².
  4. Record 9.45 × 10⁹.

Slide 7 of 8 · Straighten a curve: plot against 1/r²

Key ideas

Fixed charges Q₁ = 3.00 μC and Q₂ = 2.00 μC. Use sizes only, no minus sign. F against r is a curve. A curve has no single slope: rise over run changes with every pair of points.

Coulomb’s law: F = kQ₁Q₂ × (1/r²). F is proportional to 1/r², not to r.

So plot F against 1/r². Then F = (kQ₁Q₂)(1/r²) matches y = mx: a straight line with slope kQ₁Q₂. For r = 0.500 m: 0.500² = 0.250 and 1 ÷ 0.250 = 4.00 m⁻².

The charges are in the slope, so divide the slope by Q₁Q₂ to get k. The slope unit is N ÷ m⁻² = N·m². Add the unit N·m²/C² yourself.

Example

Q₁ = 3.00 μC and Q₂ = 2.00 μC. Points C = (2.0 m⁻², 0.108 N) and D = (10.0 m⁻², 0.524 N) lie on the line of F against 1/r². Find k.

  1. Slope = (0.524 − 0.108) N ÷ (10.0 − 2.0) m⁻² = 0.0520 N·m².
  2. Slope = kQ₁Q₂, the charge product is (3.00 × 10⁻⁶)(2.00 × 10⁻⁶) = 6.00 × 10⁻¹² C², so k = 0.0520 ÷ (6.00 × 10⁻¹²).
  3. k = 8.67 × 10⁹ N·m²/C².

Try it

Two equal charges, Q₁ = Q₂ = 4.00 μC. A line of F against 1/r² passes through G = (2.0 m⁻², 0.31 N) and H = (8.0 m⁻², 1.20 N). Find the experimental value of Coulomb’s constant.

  1. Slope = (1.20 − 0.31) N ÷ (8.0 − 2.0) m⁻² = 0.890 ÷ 6.0 = 0.1483 N·m².
  2. Charge product = (4.00 × 10⁻⁶ C)² = 1.60 × 10⁻¹¹ C².
  3. k = slope ÷ (Q₁Q₂) = 0.1483 ÷ (1.60 × 10⁻¹¹) = 9.27 × 10⁹ N·m²/C².

Slide 8 of 8 · Method: how to straighten a curve

Key ideas

Step 1: name the relationship. Force is proportional to 1/r², not to r. Step 2: plot against the quantity the law is proportional to: 1/r².

Step 3: make the new column: square each r, then flip it. Keep an extra digit until the column is done.

Step 4: plot the new column on the horizontal axis. Draw one line of best fit.

Step 5: read the slope. It holds every constant, so divide by the ones you know. Check: the points fall on a line near the origin, and the slope unit is the vertical unit ÷ m⁻².

Example

Q₁ = 3.00 μC and Q₂ = 2.00 μC, with separations 1.00, 0.707, 0.500 and 0.316 m. Points C = (2.0 m⁻², 0.108 N) and D = (10.0 m⁻², 0.524 N) lie on the line of F against 1/r². Find k. Write each step number beside your work.

  1. Step 1: F = kQ₁Q₂ × (1/r²), so F is proportional to 1/r². Step 2: plot F against 1/r².
  2. Step 3: 0.500² = 0.250 and 1 ÷ 0.250 = 4.00. The column is 1.00, 2.00, 4.00 and 10.0 m⁻².
  3. Steps 4 and 5: slope = (0.524 − 0.108) ÷ (10.0 − 2.0) = 0.0520 N·m².
  4. The charge product is (3.00 × 10⁻⁶)(2.00 × 10⁻⁶) = 6.00 × 10⁻¹² C², so k = 0.0520 ÷ (6.00 × 10⁻¹²) = 8.67 × 10⁹ N·m²/C².

Try it

Q₁ = 2.00 μC and Q₂ = 6.00 μC. Points P = (4.0 m⁻², 0.43 N) and R = (12.0 m⁻², 1.29 N) lie on the line of F against 1/r². Find the experimental value of Coulomb’s constant. Write each step number beside your work.

  1. Steps 1 and 2: F is proportional to 1/r², so the line is F against 1/r² and the slope is kQ₁Q₂.
  2. Step 5: slope = (1.29 − 0.43) ÷ (12.0 − 4.0) = 0.86 ÷ 8.0 = 0.1075 N·m².
  3. The charge product is (2.00 × 10⁻⁶)(6.00 × 10⁻⁶) = 1.20 × 10⁻¹¹ C².
  4. k = 0.1075 ÷ (1.20 × 10⁻¹¹) = 8.96 × 10⁹ N·m²/C².

Answer the practice problems online · Completed notes and worked key

B5-N01

B5-N01. A line of best fit passes through (0.5 s, 1.2 m) and (4.5 s, 5.2 m). Find its slope in m/s.

  1. Givens: two points on the line, (0.50 s, 1.20 m) and (4.50 s, 5.20 m). Question: the slope.
  2. Slope = (y₂ − y₁) ÷ (x₂ − x₁).
  3. = (5.2 − 1.2) ÷ (4.5 − 0.5) = 1.00 m/s.
  4. Answer: 1.00 m/s

B5-N02

B5-N02. Two charges are fixed. A student measures the force F at several separations r and wants a straight-line graph. Which pair of axes works?

  1. F on the vertical axis, 1/r² on the horizontal axis
  2. F on the vertical axis, r on the horizontal axis
  3. r on the vertical axis, F on the horizontal axis
  4. F on the vertical axis, r² on the horizontal axis
  1. Givens: F = kq₁q₂/r² with the charges fixed. Question: which axes give a line.
  2. F is proportional to 1/r². Plotting F against 1/r² follows y = mx with m = kq₁q₂.
  3. F against r is a curve. F against r² is also a curve, because F gets smaller as r² gets larger.
  4. Answer: A. F on the vertical axis, 1/r² on the horizontal axis

B5-N03

B5-N03. A line of best fit is drawn for scattered data points. Which description is correct?

  1. It must pass through every data point.
  2. It must start at the origin.
  3. It joins the first point to the last point.
  4. It follows the overall trend, with points above and below it.
  1. Givens: scattered measurements. Question: what a line of best fit is.
  2. The line shows the trend. Measurement error puts points on both sides, so some points sit above and some below.
  3. Answer: D. It follows the overall trend, with points above and below it.

B5-N04

B5-N04. An experiment gives the line F = (40.0 N/m)x + 0.30 N, with data from x = 0.010 m to 0.080 m. Find the extension x that the line predicts for F = 2.70 N.

  1. Givens: F = (40.0 N/m)x + 0.30 N; F = 2.70 N. Question: x.
  2. Solve for x: x = (F − b) ÷ m.
  3. x = (2.7 − 0.3) ÷ 40.0 = 0.0600 m.
  4. This is inside the measured range (0.010–0.080 m), so it is interpolation and is reliable.
  5. Answer: 0.0600 m

B5-N05

B5-N05. A graph of electric field strength E against 1/r² from a point charge is a straight line through the origin with slope 5390 N·m²/C. Use k = 8.99 × 10⁹ N·m²/C². Find the source charge in coulombs.

  1. Givens: slope = 5390 N·m²/C; k = 8.99 × 10⁹ N·m²/C². Question: Q.
  2. E = kQ(1/r²) matches y = mx, so the slope = kQ.
  3. Q = slope ÷ k = 5390 ÷ (8.99 × 10⁹) = 6.00 × 10⁻⁷ C.
  4. Answer: 6.00 × 10⁻⁷ C

B5-N06

B5-N06. A student extends the line F = (25.0 N/m)x + 0.50 N to x = 0.30 m, but all the measurements were made between x = 0.02 m and 0.12 m. Predict F and say whether you trust it.

  1. Givens: F = (25.0 N/m)x + 0.50 N; data only from 0.02 m to 0.12 m. Question: F at 0.30 m and how reliable it is.
  2. F = 25.0(0.30) + 0.50 = 8.0 N.
  3. 0.30 m is far outside the measured range, so this is extrapolation. The spring may stop following a straight line (it could stretch permanently), so the prediction is not reliable.

B5-N07

B5-N07. Two charges q₁ = 2.0 × 10⁻⁶ C and q₂ are fixed. The force on q₂ is 5.39 N at r = 0.100 m and 0.599 N at r = 0.300 m. Plot F against 1/r². Find the slope in N·m², using these two points.

  1. Givens: F = 5.39 N at r = 0.100 m; F = 0.599 N at r = 0.300 m. Question: the slope of F against 1/r².
  2. Convert: 1/r² = 1 ÷ 0.100² = 100 m⁻² and 1 ÷ 0.300² = 11.1 m⁻².
  3. Slope = (5.39 − 0.599) ÷ (100 − 11.1) = 0.0539 N·m² (about 0.054).
  4. The unit is N ÷ m⁻² = N·m².
  5. Answer: 0.0539 N·m²

B5-N08

B5-N08. Use your slope from the previous question (0.0539 N·m²) and k = 8.99 × 10⁹ N·m²/C² to find q₂, given q₁ = 2.0 × 10⁻⁶ C. Explain what the line would show about the force if q₂ were doubled.

  1. Givens: slope = kq₁q₂ = 0.0539 N·m²; q₁ = 2.0 × 10⁻⁶ C. Question: q₂, and the effect of doubling q₂.
  2. q₂ = slope ÷ (kq₁) = 0.0539 ÷ ((8.99 × 10⁹)(2.0 × 10⁻⁶)) = 3.00 × 10⁻⁶ C.
  3. If q₂ doubled, the slope kq₁q₂ would double, so the line would be twice as steep.