B11 · Worked examples

Every question here uses the same chain as B10, but the unknown changes. It may be a current, a time, an ion charge, a mass lost or gained, or moles of gas. First find which end of the chain is given. Then walk toward the unknown. Here I is current in amperes (A), t is time, and q is charge in coulombs (C). Also n(e⁻) is moles of electrons, M is molar mass, and z is the number of electrons in the half-reaction for one ion. F = 9.65 × 10⁴ C/mol e⁻ is the Faraday constant.

Open the B11 lesson · B11 slide notes

Worked question types

Each example shows every step, why you do it, and the idea behind it.

Question type

Choose where the chain starts and which way to walk

Use this when: The question gives some quantities and asks for another. You need a plan before any numbers are used.

Example. Problem A: nickel is plated from Ni²⁺ by 2.00 A for 30.0 minutes, and you must find the mass. Problem B: a cathode must gain 0.500 g of nickel in 30.0 minutes, and you must find the current. For each problem, say which end of the chain is given, which way you walk, and list the calculation steps.
  1. Write the chain.

    Use Method: how to solve a Faraday problem when the unknown changes. Current and time give charge. Charge gives moles of electrons. The half-reaction gives moles of metal. Molar mass gives mass.

    I, t → q → n(e⁻) → n(Ni) → m

  2. Mark the given end and the asked end in Problem A.

    Current and time are given and the mass is asked. The mass is at the far end, so you walk forward.

    Problem A: forward from I and t to m

  3. List the forward steps.

    Multiply for charge. Divide by F. Divide by the coefficient of e⁻. Multiply by M.

    q = It, n(e⁻) = q ÷ F, n(Ni) = n(e⁻) ÷ 2, m = nM

  4. Mark the ends in Problem B.

    The mass is given and the current is asked. The current is at the near end, so you walk backward.

    Problem B: backward from m to I

  5. List the backward steps.

    Every step reverses. Divide by M. Multiply by the coefficient of e⁻. Multiply by F. Divide the charge by the time in seconds.

    n = m ÷ M, n(e⁻) = 2n, q = n(e⁻) × F, I = q ÷ t

  6. Check that a step reverses cleanly.

    Take 0.0250 mol of nickel. Going back to electrons multiplies by 2. Going forward again divides by 2 and returns the start.

    0.0250 × 2 = 0.0500 mol e⁻, 0.0500 ÷ 2 = 0.0250 mol Ni ✓

Why this works. The chain has a fixed order. Where your given sits decides the direction. Walking forward divides by F and by the coefficient. Walking backward multiplies by them.

Check your answer. A plan with the right direction ends in the unit the question asks for: grams for A and amperes for B.

Common mistake. Dividing by the coefficient of e⁻ when you are walking backward. Backward steps multiply.

Answer: Problem A walks forward: q = It, ÷ F, ÷ 2, × M. Problem B walks backward: ÷ M, × 2, × F, then ÷ t

Question type

Find the current

Use this when: The question gives a mass and a time, and asks for the constant current.

Example. A cathode gains 0.800 g of nickel in 25.0 minutes from Ni²⁺ solution. The molar mass of nickel is 58.69 g/mol. What constant current was used?
  1. Write the givens as symbols with units.

    This shows that the time needs converting.

    m = 0.800 g Ni, t = 25.0 min, M = 58.69 g/mol. Asked: I

  2. Start at the mass and walk backward.

    Moles of nickel equal mass divided by molar mass.

    n(Ni) = 0.800 ÷ 58.69 = 0.01363 mol

  3. Find the moles of electrons.

    Ni²⁺ + 2e⁻ → Ni needs 2 electrons per atom. Going backward, multiply.

    n(e⁻) = 2 × 0.01363 = 0.02726 mol

  4. Find the charge.

    Moles to coulombs means multiply by F.

    q = 0.02726 × (9.65 × 10⁴) = 2631 C

  5. Change the time to seconds.

    An ampere needs seconds.

    25.0 × 60 = 1500 s

  6. Find the current.

    Current is charge divided by time. Round the final answer to three significant digits.

    I = 2631 ÷ 1500 = 1.754 A → 1.75 A

Why this works. The current is the charge that moved each second. The mass fixes the total charge. Dividing that charge by the time in seconds gives the charge each second.

Check your answer. About 0.0136 mol of nickel needs about 0.027 mol of electrons, about 2600 C. Over 1500 s that is about 1.7 A.

Common mistake. Leaving the time in minutes. The current then comes out 60 times too large.

Answer: I = 1.75 A

Question type

Find the charge on an ion

Use this when: The question gives the current, the time, the mass deposited and the molar mass, but no half-reaction. It asks for the ion charge.

Example. A metal with a molar mass of 196.97 g/mol is plated from a solution of its ions. A current of 2.00 A runs for 25.0 minutes and 2.04 g of metal is deposited. Find the charge on the metal ion and write the half-reaction.
  1. Name the unknown.

    Let z be the number of electrons each ion gains. It equals the ion charge.

    z = n(e⁻) ÷ n(metal)

  2. Find the charge.

    Change 25.0 min to 1500 s first. Then multiply by the current.

    q = 2.00 × 1500 = 3000 C

  3. Find the moles of electrons.

    Divide by F.

    n(e⁻) = 3000 ÷ (9.65 × 10⁴) = 0.03109 mol

  4. Find the moles of metal.

    Use the mass and the molar mass.

    n(metal) = 2.04 ÷ 196.97 = 0.01036 mol

  5. Divide electrons by metal.

    This gives the electrons for each atom of metal.

    z = 0.03109 ÷ 0.01036 = 3.00

  6. Round to a whole number.

    Ion charges are whole numbers. A value this close to 3 means z = 3.

    z = 3, so the ion is M³⁺

  7. Write the half-reaction.

    The ion gains 3 electrons.

    M³⁺ + 3e⁻ → M

Why this works. A mole of electrons is spread over the moles of metal. The ratio of the two is the number of electrons each ion needs. That number is the charge on the ion.

Check your answer. The ratio is within 0.01 of a whole number. A ratio such as 2.5 would mean an error in the data or the arithmetic.

Common mistake. Reporting the ratio as 3.00 or 3.0009. The ion charge is a whole number, so state 3.

Answer: z = 3. The ion is M³⁺ and the half-reaction is M³⁺ + 3e⁻ → M

Question type

Find the mass lost and gained in a voltaic cell

Use this when: The question describes a voltaic cell that delivers a steady current for a time, and asks for the mass lost by the anode and gained by the cathode.

Example. A voltaic cell has a nickel anode and a silver cathode. It delivers a steady 0.250 A for 2.00 hours. The molar masses are 58.69 g/mol for nickel and 107.87 g/mol for silver. Find the mass lost by the anode and the mass gained by the cathode.
  1. Write the half-reactions.

    The anode is where oxidation happens. The cathode is where reduction happens.

    Anode: Ni → Ni²⁺ + 2e⁻ Cathode: Ag⁺ + e⁻ → Ag

  2. Find the charge.

    Change 2.00 h to 7200 s. Then multiply by the current.

    q = 0.250 × 7200 = 1800 C

  3. Find the moles of electrons.

    The same electrons flow through the anode and the cathode. Divide by F.

    n(e⁻) = 1800 ÷ (9.65 × 10⁴) = 0.01865 mol

  4. Use the anode half-reaction.

    Nickel gives 2 electrons per atom, so divide by 2.

    n(Ni) = 0.01865 ÷ 2 = 0.009325 mol

  5. Find the mass lost by the anode.

    Multiply by the molar mass. The anode is oxidized, so it loses mass.

    m = 0.009325 × 58.69 = 0.5473 g → 0.547 g

  6. Use the cathode half-reaction.

    Silver takes 1 electron per atom, so the moles of silver equal the moles of electrons.

    n(Ag) = 0.01865 ÷ 1 = 0.01865 mol

  7. Find the mass gained by the cathode.

    Multiply by the molar mass. The cathode gains the metal.

    m = 0.01865 × 107.87 = 2.012 g → 2.01 g

Why this works. The electrons in the wire come from the anode half-reaction and are used in the cathode half-reaction. So one charge fixes the amount that reacts at both electrodes. Each electrode has its own ratio and its own molar mass.

Check your answer. The anode loses mass and the cathode gains mass. Silver has twice as many moles as nickel here, and a larger molar mass, so its mass is much bigger.

Common mistake. Using the moles of nickel for silver. The two metals have different electron ratios, so their moles differ.

Answer: The nickel anode loses 0.547 g. The silver cathode gains 2.01 g

Question type

Find the moles of gas formed at inert electrodes

Use this when: The question gives a current and a time for an aqueous solution with inert electrodes, and asks for the moles or mass of the gases.

Example. A solution of Na₂SO₄(aq) is electrolyzed with inert electrodes at 1.75 A for 25.0 minutes. The reduction is 2H₂O + 2e⁻ → H₂ + 2OH⁻ and the oxidation is 2H₂O → O₂ + 4H⁺ + 4e⁻. Find the moles of H₂ and O₂ formed and the mass of H₂. The molar mass of H₂ is 2.02 g/mol.
  1. Find the charge.

    Change 25.0 min to 1500 s. The current supplies the electrons at both electrodes, so one charge feeds both half-reactions.

    q = 1.75 × 1500 = 2625 C

  2. Find the moles of electrons.

    Divide by F.

    n(e⁻) = 2625 ÷ (9.65 × 10⁴) = 0.02720 mol

  3. Use the reduction for hydrogen.

    Two electrons make one H₂, so divide by 2.

    n(H₂) = 0.02720 ÷ 2 = 0.01360 mol → 0.0136 mol

  4. Find the mass of hydrogen.

    Multiply the middle value by the molar mass. The question asks for grams here.

    m(H₂) = 0.01360 × 2.02 = 0.02747 g → 0.0275 g

  5. Use the oxidation for oxygen.

    Four electrons make one O₂, so divide the same moles of electrons by 4.

    n(O₂) = 0.02720 ÷ 4 = 0.006800 mol → 0.00680 mol

  6. Check the ratio.

    The overall reaction 2H₂O → 2H₂ + O₂ makes 2 mol of hydrogen for each mole of oxygen.

    0.01360 ÷ 0.006800 = 2.000 ✓

Why this works. The same electrons pass through the whole circuit. Each half-reaction uses its own coefficient of e⁻. Hydrogen needs 2 electrons per molecule and oxygen needs 4, so there is twice as much hydrogen.

Check your answer. There is twice as much hydrogen as oxygen, which matches the overall reaction.

Common mistake. Dividing by 2 for oxygen. Use the 4 from the oxidation half-reaction.

Answer: n(H₂) = 0.0136 mol, m(H₂) = 0.0275 g, n(O₂) = 0.00680 mol

Question type

Find the time to make a given amount of gas

Use this when: The question gives the moles of a gas to be made, and a current, and asks for the time.

Example. A solution of Na₂SO₄(aq) is electrolyzed with inert electrodes at a steady 1.50 A. The oxidation is 2H₂O → O₂ + 4H⁺ + 4e⁻. How long, in minutes, must the current run to make 0.0125 mol of O₂?
  1. Start at the gas and walk backward.

    The moles of oxygen are given. The time is the last link.

    Given: n(O₂) = 0.0125 mol, I = 1.50 A. Asked: t in minutes

  2. Find the moles of electrons.

    Four electrons make each O₂, so multiply by 4.

    n(e⁻) = 4 × 0.0125 = 0.05000 mol

  3. Find the charge.

    Multiply by F.

    q = 0.05000 × (9.65 × 10⁴) = 4825 C

  4. Find the time in seconds.

    Divide the charge by the current.

    t = 4825 ÷ 1.50 = 3217 s

  5. Change to minutes.

    The question asks for minutes. Divide by 60 and round the final answer to three significant digits.

    3217 ÷ 60 = 53.62 min → 53.6 min

Why this works. Walking backward reverses each step. The 4 in the oxidation half-reaction is the key number. A bigger current would shorten the time.

Check your answer. About 0.05 mol of electrons is about 4800 C. At 1.5 C each second that is a little over 3000 s.

Common mistake. Using 2 for oxygen because hydrogen uses 2. Each gas has its own coefficient.

Answer: t = 53.6 min

Question type

Use the mass gained from two weighings to find a time

Use this when: The question gives the mass of a cathode before and after plating, and asks for the time or the current.

Example. A cathode has a mass of 18.350 g before silver plating and 19.020 g after. The current was a steady 1.50 A and the half-reaction is Ag⁺ + e⁻ → Ag. The molar mass of silver is 107.87 g/mol. How long did the plating run, in minutes?
  1. Subtract to find the mass deposited.

    The cathode already had 18.350 g. The current made only the gain.

    19.020 − 18.350 = 0.670 g

  2. Find the moles of silver.

    Divide the gain by the molar mass.

    n(Ag) = 0.670 ÷ 107.87 = 0.006211 mol

  3. Find the moles of electrons.

    One electron makes one silver atom. The ratio is 1 to 1, but show the step.

    n(e⁻) = 1 × 0.006211 = 0.006211 mol

  4. Find the charge.

    Multiply by F.

    q = 0.006211 × (9.65 × 10⁴) = 599.4 C

  5. Find the time in seconds and then minutes.

    Divide by the current. Then divide by 60, and round the final answer to three significant digits.

    t = 599.4 ÷ 1.50 = 399.6 s 399.6 ÷ 60 = 6.660 min → 6.66 min

Why this works. Two weighings of an electrode are a signal to subtract. Only the gain was made by the current. Using the final mass would credit the current with metal that was already there.

Check your answer. The final mass, 19.020 g, would give a time about 28 times too large. A time near 7 minutes fits 0.670 g at 1.50 A.

Common mistake. Using the final mass, 19.020 g, as the mass deposited.

Answer: t = 6.66 min

Question type

Find the mass lost at an anode

Use this when: The question describes an electrode that dissolves, such as an impure copper anode in refining, and asks for the mass it loses.

Example. In copper refining, an impure copper anode dissolves and pure copper plates onto the cathode. A steady 4.00 A runs for 1.50 hours. The molar mass of copper is 63.55 g/mol. What mass of copper dissolves from the anode, and what mass does an ideal cathode gain?
  1. Write the anode half-reaction.

    Copper is oxidized at the anode, so it loses electrons.

    Cu → Cu²⁺ + 2e⁻

  2. Find the charge.

    Change 1.50 h to 5400 s. Then multiply by the current.

    q = 4.00 × 5400 = 2.160 × 10⁴ C

  3. Find the moles of electrons.

    Divide by F.

    n(e⁻) = 2.160 × 10⁴ ÷ (9.65 × 10⁴) = 0.2238 mol

  4. Find the moles of copper.

    Each copper atom gives 2 electrons, so divide by 2.

    n(Cu) = 0.2238 ÷ 2 = 0.1119 mol

  5. Find the mass lost.

    Multiply by the molar mass. Round the final answer to three significant digits.

    m = 0.1119 × 63.55 = 7.111 g → 7.11 g

  6. Find the ideal cathode gain.

    At the cathode, Cu²⁺ + 2e⁻ → Cu uses the same electrons and the same 2 to 1 ratio. So the gain is the same.

    the cathode gains 7.11 g

Why this works. The electrons that leave the anode arrive at the cathode, so the chain works at both. In an ideal cell with the same ion and the same ratio, the loss and the gain are equal.

Check your answer. A current of about 4 A for 5400 s moves about 22 000 C. That is about 0.22 mol of electrons and about 0.11 mol of copper, about 7 g.

Common mistake. Leaving the time in hours. The time must be in seconds.

Answer: The anode loses 7.11 g. An ideal cathode gains 7.11 g

Question type

Find and repair a wrong direction in the chain

Use this when: The question shows a student solution that divides when it should multiply, or the reverse, and asks you to find the error and correct the answer.

Example. A student finds the current needed to plate 0.950 g of copper in 30.0 minutes from Cu²⁺ + 2e⁻ → Cu. After finding 0.01495 mol of copper, the student divides by 2 to get the moles of electrons. The molar mass of copper is 63.55 g/mol. Find the error and the correct current.
  1. Say which way the student is walking.

    The mass is given and the current is asked, so the walk is backward from metal to electrons.

    metal → electrons is a backward step

  2. Find the student’s current.

    This shows how far off the answer is.

    n(e⁻) = 0.01495 ÷ 2 = 0.007475 mol q = 0.007475 × (9.65 × 10⁴) = 721.3 C I = 721.3 ÷ 1800 = 0.401 A

  3. Repair the step.

    Each copper atom needs 2 electrons, so there are twice as many electrons as copper atoms. Multiply by 2.

    n(e⁻) = 2 × 0.01495 = 0.02990 mol

  4. Find the charge.

    Multiply by F.

    q = 0.02990 × (9.65 × 10⁴) = 2885 C

  5. Find the current.

    Divide by the time, 30.0 min = 1800 s. Round the final answer to three significant digits.

    I = 2885 ÷ 1800 = 1.603 A → 1.60 A

  6. Compare the two answers.

    One wrong step in the chain carries into every later number. Here it makes the answer 4 times too small.

    1.60 ÷ 0.401 is about 4

Why this works. The half-reaction says 2 electrons for each atom. Going from metal back to electrons multiplies by 2. Dividing instead applies the forward rule in the backward direction.

Check your answer. A wrong ratio is used twice. It changes the moles of electrons, and the charge and the current follow. So the error is a factor of 2 × 2 = 4.

Common mistake. Dividing when you should multiply. Check the direction of every step before you calculate.

Answer: The student divided instead of multiplying. The correct current is 1.60 A

Diploma-style questions

Try each question first. Then open the worked solution.

Numerical response · outcome 30-B2.8k
A cathode gains 0.640 g of copper in 20.0 minutes from Cu²⁺ + 2e⁻ → Cu. The molar mass of copper is 63.55 g/mol. What constant current was used? Record your answer as a.bc A. Enter the digits a, b and c.
Show the worked solution (try the question first)
  1. Find the moles of copper.

    Start from the mass and walk backward.

    n(Cu) = 0.640 ÷ 63.55 = 0.01007 mol

  2. Find the moles of electrons.

    Two electrons make each copper atom, so multiply by 2.

    n(e⁻) = 2 × 0.01007 = 0.02014 mol

  3. Find the charge.

    Multiply by F.

    q = 0.02014 × (9.65 × 10⁴) = 1944 C

  4. Find the current.

    Change 20.0 min to 1200 s, then divide the charge by the time. Round to three significant digits.

    I = 1944 ÷ 1200 = 1.620 A → 1.62 A

  5. Enter the digits.

    The value is 1.62, so a = 1, b = 6 and c = 2.

    record 1 6 2

Answer: 1.62 A. Record 1 6 2.

Multiple choice · outcome 30-B2.8k
A metal with a molar mass of 58.69 g/mol is plated from a solution of its ions. A current of 1.50 A runs for 40.0 minutes and deposits 1.10 g of the metal. What is the charge on the metal ion?
  1. A. 1+
  2. B. 2+
  3. C. 3+
  4. D. 4+
Show the worked solution (try the question first)
  1. Find the moles of electrons.

    Change 40.0 min to 2400 s. Charge is It. Then divide by F.

    q = 1.50 × 2400 = 3600 C n(e⁻) = 3600 ÷ (9.65 × 10⁴) = 0.03731 mol

  2. Find the moles of metal.

    Divide the mass by the molar mass.

    n(metal) = 1.10 ÷ 58.69 = 0.01874 mol

  3. Divide electrons by metal.

    This gives the electrons each ion gains.

    z = 0.03731 ÷ 0.01874 = 1.99

  4. Round to a whole number.

    The ion charge is a whole number.

    z = 2, so the charge is 2+

Why each choice is right or wrong

  • A. If z were 1, the moles of electrons would equal the moles of metal, 0.01874 mol. The measured value is 0.03731 mol, twice as large.
  • B. Correct. 0.03731 ÷ 0.01874 = 1.99, which rounds to 2.
  • C. If z were 3, the electrons needed would be 0.05622 mol. The measured value is 0.03731 mol.
  • D. If z were 4, the electrons needed would be 0.07496 mol. The measured value is 0.03731 mol.

Answer: B

Multiple choice · outcome 30-B2.8k
A voltaic cell has a nickel anode and a copper cathode. It delivers 0.400 A for 60.0 minutes. The half-reactions are Ni → Ni²⁺ + 2e⁻ and Cu²⁺ + 2e⁻ → Cu. The molar masses are 58.69 g/mol for nickel and 63.55 g/mol for copper. Which statement is correct?
  1. A. The nickel anode gains 0.438 g and the copper cathode loses 0.474 g.
  2. B. The nickel anode loses 0.438 g and the copper cathode gains 0.474 g.
  3. C. The nickel anode loses 0.438 g and the copper cathode gains 0.438 g, because the moles are equal.
  4. D. The nickel anode loses 0.876 g and the copper cathode gains 0.948 g.
Show the worked solution (try the question first)
  1. Find the charge and the moles of electrons.

    Change 60.0 min to 3600 s. Charge is It. Then divide by F.

    q = 0.400 × 3600 = 1440 C n(e⁻) = 1440 ÷ (9.65 × 10⁴) = 0.01492 mol

  2. Use each half-reaction.

    Both use 2 electrons per atom, so the moles are equal.

    n(Ni) = n(Cu) = 0.01492 ÷ 2 = 0.007460 mol

  3. Find the masses.

    The anode loses mass and the cathode gains mass. The molar masses differ, so the masses differ.

    nickel: 0.007460 × 58.69 = 0.4378 g → 0.438 g copper: 0.007460 × 63.55 = 0.4741 g → 0.474 g

Why each choice is right or wrong

  • A. The roles are reversed. Oxidation happens at the anode, so nickel is used up and the anode loses mass. Copper plates on the cathode.
  • B. Correct. Both electrodes handle 0.007460 mol. The anode loses 0.438 g and the cathode gains 0.474 g.
  • C. The moles are equal, but the molar masses are not. Copper has a larger molar mass, so its mass is 0.474 g, not 0.438 g.
  • D. These masses use the moles of electrons, 0.01492 mol, as if the ratio were 1 to 1. Each metal needs 2 electrons per atom, so divide by 2 first.

Answer: B

Numerical response · outcome 30-B2.8k
A solution of Na₂SO₄(aq) is electrolyzed with inert electrodes at 3.00 A for 30.0 minutes. The oxidation is 2H₂O → O₂ + 4H⁺ + 4e⁻. Find the moles of O₂ formed. Record your answer as 0.0abc mol. Enter the digits a, b and c.
Show the worked solution (try the question first)
  1. Find the charge.

    Change 30.0 min to 1800 s. Charge is It.

    q = 3.00 × 1800 = 5400 C

  2. Find the moles of electrons.

    Divide by F.

    n(e⁻) = 5400 ÷ (9.65 × 10⁴) = 0.05596 mol

  3. Use the oxidation half-reaction.

    Four electrons make each O₂, so divide by 4. Round to three significant digits.

    n(O₂) = 0.05596 ÷ 4 = 0.01399 mol → 0.0140 mol

  4. Enter the digits.

    The value is 0.0140, so a = 1, b = 4 and c = 0.

    record 1 4 0

Answer: 0.0140 mol. Record 1 4 0.