B15 · Worked examples
These questions move a conductor or a magnet through a magnetic field. You find which end becomes positive, how large the potential difference is, which way the current goes, or how the induced current fights the motion.
Open the B15 lesson · B15 notes and practice
Method slides in this lesson: “Method: how to find an induced voltage and its direction”. Find them in the lesson slides, with the steps for each skill in one place.
Worked question types
Each example shows every step, why you do it, and the idea behind it.
Question typeFind which end of a moving rod becomes positive
Use this when: A metal rod is pulled through a magnetic field. The question asks which end becomes positive, or which end becomes negative.
Method slide in the lesson: “Method: how to find an induced voltage and its direction”. Its numbered steps give the order; the steps below add the reason for each.
Example. A vertical metal rod is pulled to the left through a uniform magnetic field that points into the page. (a) Which end of the rod, top or bottom, becomes positive? (b) The field is reversed to point out of the page. Which end is positive now?
- Part (a): find the force on positive charge.
The charges in the rod move left with the rod. Put the thumb along the velocity and the fingers along the field. The palm shows the force on a positive charge.
thumb left, fingers into the page, palm faces down
- Reverse for electrons.
The charges that move in a metal are electrons, and they are negative. Their force is opposite to the palm.
electrons are pushed up
- Say which end is positive.
Electrons pile up at the top, so the top becomes negative. The bottom has lost electrons, so it becomes positive.
bottom end positive
- Part (b): reverse the field.
Reversing the field reverses the force. The electrons are now pushed down, so the bottom is negative and the top is positive.
top end positive
Why this works. Pulling the rod pulls its electrons through the field. Each electron feels a magnetic force, so charge is pushed to one end. That makes a potential difference between the ends.
Check your answer. Reversing either the motion or the field swaps the two ends. Reversing both leaves the ends where they were.
Common mistake. Forgetting to reverse for electrons. Also thinking the rod becomes a magnet. It only becomes charged at its ends.
Answer: (a) The bottom end is positive. (b) The top end is positive.
Question typeFind the potential difference across a moving rod
Use this when: The question gives the rod’s length, speed and the field strength, and asks for the potential difference. The equation ΔV = Blv is given to you on the exam.
Method slide in the lesson: “Method: how to find an induced voltage and its direction”. Its numbered steps give the order; the steps below add the reason for each.
Example. A rod 0.45 m long moves at 2.5 m/s at right angles to a uniform magnetic field of 0.320 T. It also moves at right angles to its own length. Find the potential difference between the ends of the rod.
- Write the equation.
The three quantities multiply. It is not on the data sheet, so an exam question will give it to you.
ΔV = Blv
- Check the units.
Use tesla, metres and metres per second. These give volts.
B = 0.320 T, l = 0.45 m, v = 2.5 m/s
- Substitute.
Multiply the three numbers.
ΔV = (0.320)(0.45)(2.5) = 0.360 V
Why this works. A faster rod gives each electron a bigger push. A longer rod gives the push more distance. A stronger field gives a bigger force. The effects multiply.
Check your answer. Check the units: 1 T × 1 m × 1 m/s = 1 V, so tesla × metres × metres per second gives volts.
Common mistake. Using centimetres for the length. Also using a rod speed that is not at right angles to the field.
Answer: ΔV = 0.360 V
Question typeFind the speed of the rod from the potential difference
Use this when: The question gives the potential difference, the field and the rod length, and asks for the speed or one of the other quantities.
Method slide in the lesson: “Method: how to find an induced voltage and its direction”. Its numbered steps give the order; the steps below add the reason for each.
Example. The potential difference between the ends of a 0.80 m rod is 1.20 V. The rod moves at right angles to a 0.250 T field and to its own length. Find the speed of the rod.
- Write the equation.
This is the same equation as before.
ΔV = Blv
- Solve for the speed.
Divide both sides by B and l.
v = ΔV ÷ (Bl)
- Substitute.
Put the bottom in brackets so you divide by both B and l.
v = 1.20 ÷ [(0.250)(0.80)] = 6.00 m/s
Why this works. The same equation gives any one of the four quantities if you know the other three. Rearrange first, then put in the numbers.
Check your answer. Put the speed back in. (0.250)(0.80)(6.00) = 1.20 V. It matches.
Common mistake. Multiplying by B and l instead of dividing. Also mixing up the roles of the speed and the rod length.
Answer: v = 6.00 m/s
Question typeFind the direction of the current in a circuit with a moving rod
Use this when: The rod slides on two rails, which are parallel metal bars. A resistor, a part that uses up electrical energy, joins them. The question asks which way conventional current goes.
Method slide in the lesson: “Method: how to find an induced voltage and its direction”. Its numbered steps give the order; the steps below add the reason for each.
Example. A vertical rod slides on two horizontal rails. The rails are joined by a resistor at their left ends. A uniform magnetic field points into the page. The rod is pulled to the right. Does conventional current go up or down through the resistor? Does it go clockwise or counterclockwise?
- Find the positive end of the rod.
Thumb right along the velocity, fingers into the page. The palm faces up, which is the force on positive charge. Electrons are pushed down.
bottom end negative, top end positive
- Treat the rod as a battery.
Conventional current leaves the positive end. It leaves the top of the rod and moves left along the top rail.
out of the top end, left along the top rail
- Follow the circuit.
It goes through the resistor and back along the bottom rail to the rod. Down the resistor, then right along the bottom rail.
down through the resistor, right along the bottom rail
- Finish the loop.
Inside the rod, current goes from the negative end to the positive end, so up the rod.
up through the rod
- Name the sense of the loop.
The top rail current goes left and the bottom rail current goes right. That is counterclockwise.
counterclockwise
Why this works. The moving rod acts like a battery. Its positive end is the one found with the right hand and then reversed for electrons. Current comes out of the positive end and goes round the circuit.
Check your answer. Pull the rod to the left, or reverse the field, and the current reverses. It would then go clockwise.
Common mistake. Tracing electron flow when the question asks for conventional current. Also tracing in the wrong direction inside the rod.
Answer: Conventional current goes down through the resistor. It goes counterclockwise.
Question typePredict what the meter does when a magnet and a coil move
Use this when: The question changes the pole, the direction or the speed of a magnet near a coil and asks what the meter does.
Example. Pushing the south pole of a bar magnet into a coil at a steady speed makes the meter needle swing to the right. What does the needle do in each case? (a) The south pole is pulled out at the same speed. (b) The north pole is pushed in at the same speed. (c) The south pole is pushed in twice as fast. (d) The magnet is held still inside the coil.
- Start with the rule.
A current is made only while the magnet and the coil move relative to each other.
no motion, no current
- Part (a): reverse the motion.
Pulling out is the opposite motion. The current reverses.
(a) the needle swings left
- Part (b): reverse the pole.
The north pole in is the opposite of the south pole in. The current reverses.
(b) the needle swings left
- Part (c): change the speed.
Faster motion gives a bigger potential difference. The direction is the same as the first case.
(c) the needle swings right, farther
- Part (d): no motion.
A still magnet gives no current, even inside the coil.
(d) the needle stays at zero
Why this works. The coil works like a rod in a field. The wires in the coil cut across the magnet’s field only when something moves. Reversing the pole or the motion reverses the current. A faster motion makes it larger.
Check your answer. Reversing one thing reverses the current. Reversing two things gives the original direction again.
Common mistake. Saying a still magnet inside a coil gives a steady current. It does not. Nothing is cutting across the wires.
Answer: (a) left, (b) left, (c) right and larger, (d) zero.
Question typeExplain why a generator is harder to turn when it lights a lamp
Use this when: The question describes a generator that is easy to turn alone and harder to turn when connected to a load. It asks for an explanation.
Example. A hand-cranked generator is easy to turn when nothing is connected to it. It is harder to turn when it lights a lamp. Explain why, and say where the extra energy goes.
- Start with the motion.
You turn the coil in a magnetic field. This is the generator effect: motion in, electricity out.
motion → potential difference
- Add the lamp.
With the lamp connected, the circuit is closed. So there is a current in the coil.
closed circuit → current
- Use the motor effect.
A current in a magnetic field feels a magnetic force. The force on the coil’s current opposes the turning.
current in a field → force against the motion
- Follow the energy.
You do extra work against that force. The extra work becomes the electrical energy that lights the lamp.
motion energy → electrical energy → light
Why this works. A motor and a generator are the same machine used in opposite directions. The same current that the motion makes also causes a force that fights the motion. That is Lenz’s law.
Check your answer. The harder it is to turn, the more energy goes to the lamp. With no lamp there is no current, so no force and no extra work.
Common mistake. Saying the lamp makes the magnet heavier, or that friction is greater. The extra push is a magnetic force.
Answer: The turning makes a current. The current in the field feels a force against the turning. The extra work becomes the electrical energy in the lamp.
Question typeFind the direction of the Lenz force on a moving magnet
Use this when: A magnet moves near a conductor. The question asks which way the magnetic force on the magnet points, or what happens to the motion.
Method slide in the lesson: “Method: how to find an induced voltage and its direction”. Its numbered steps give the order; the steps below add the reason for each.
Example. A pendulum with a strong magnet at its end swings between two aluminium blocks. At the lowest point it moves to the right. What is the direction of the magnetic force on the magnet right now? What happens to the swing as time passes? Does the direction of this force change when the pendulum swings back to the left?
- Start with the motion.
The moving magnet makes its field move across the aluminium. By the generator effect, currents flow in the aluminium. A current made this way, by motion in a field with no battery, is called an induced current.
motion → induced currents
- Find the force.
Those currents are in a magnetic field, so they feel a force. The force on the magnet is the matching force back on the magnet.
currents in a field → force on the magnet
- Use Lenz’s law for the direction.
The force from the induced current opposes the motion that caused it. The magnet moves right, so the force is left.
right now: to the left
- Say what happens over time.
The force always works against the motion, so the swing slows and dies away quickly.
the swing dies away
- Swinging back.
On the way back the magnet moves left, so the force is to the right. It always opposes the motion.
the direction reverses
Why this works. The force is not always in one direction. It always points opposite to the velocity. The chain is motion, then induced current, then a force that opposes the motion.
Check your answer. If the force pointed along the motion, the magnet would speed up and make energy from nothing. Opposing the motion keeps energy conserved.
Common mistake. Saying the force is always left or always right. It follows the motion. Also saying the aluminium is magnetic. It is not.
Answer: The force is to the left now. The swing dies away. The force is to the right when the pendulum swings back left.
Question typeRank materials by how much they slow a falling magnet
Use this when: A magnet falls through or over rods or tubes of different materials. The question asks for the order of the fall times and why.
Example. Three rods of the same size are made of plastic, aluminium and copper. A ring magnet is dropped over the top of each rod from the same height at the same time. Copper conducts electricity better than aluminium. Plastic is an insulator. Rank the rods from the fastest fall to the slowest fall. Explain the order.
- Decide where a current can form.
A moving magnet induces a current in a conductor. An insulator carries no current.
plastic: no current
- Compare the conductors.
A better conductor carries a larger induced current for the same potential difference.
copper current > aluminium current
- Link current to the force.
A larger induced current gives a larger force. By Lenz’s law that force opposes the fall.
larger current → larger force up
- Rank the falls.
The smallest force is in plastic, and the largest is in copper.
plastic fastest, then aluminium, then copper slowest
Why this works. The braking force comes from the induced current. No current means no force. A bigger current means a bigger force against the motion. How well the material conducts decides the size of the current.
Check your answer. The magnet in plastic should fall as if it were in air, because plastic cannot carry the induced current.
Common mistake. Saying a better insulator slows the magnet more. Insulators carry no induced current. Also saying aluminium is magnetic.
Answer: Plastic is fastest, then aluminium, then copper is slowest.
Question typeCompare a free fall with a fall through a metal tube
Use this when: The question asks for the free-fall time of a magnet and then asks you to explain why it takes longer in a tube.
Example. A strong magnet is dropped from rest through 0.30 m in air. Find the time it takes. The same magnet takes 2 to 3 s to fall 0.30 m inside a vertical aluminium tube. Explain the difference. Use g = 9.81 m/s².
- Use free-fall motion.
The magnet starts from rest and falls straight down with acceleration g. Use d = ½gt².
d = ½gt²
- Solve for the time.
Multiply by 2, divide by g, and take the square root.
t = √(2d ÷ g)
- Substitute.
Use metres and g = 9.81 m/s².
t = √[2(0.30) ÷ 9.81] = 0.25 s
- Explain the longer time in the tube.
The moving magnet induces currents in the aluminium. The force on those currents pushes up on the magnet, opposing its fall.
Lenz’s law: force opposes the motion
- Say what the difference shows.
2 to 3 s is about ten times longer than 0.25 s. The upward force nearly balances gravity.
the magnet falls slowly
Why this works. In air only gravity acts, so the magnet falls freely. In the tube the induced currents add an upward force. The net downward force is small, so the fall is slow.
Check your answer. A time of about a quarter of a second for 30 cm is what you expect from dropping an object by hand. It matches.
Common mistake. Saying gravity is weaker in the tube, or that the tube is magnetic. The extra force comes from the induced current.
Answer: The time in air is 0.25 s. In the tube, induced currents give an upward force that opposes the fall, so it takes much longer.
Diploma-style questions
Try each question first. Then open the worked solution.
Multiple choice · outcome 30-B3.9kA rod moving through a magnetic field has a potential difference ΔV between its ends. A second rod is twice as long, moves at one-third the speed, and is in a field three times as strong. What is the potential difference between the ends of the second rod?
- A. ΔV ÷ 2
- B. ΔV
- C. 2ΔV
- D. 6ΔV
Show the worked solution (try the question first)
- Write the equation.
ΔV = Blv. The three factors multiply.
ΔV = Blv
- Apply each change.
The length is 2 times, the speed is ⅓ times, and the field is 3 times.
2 × ⅓ × 3 = 2
- Write the new potential difference.
The potential difference is multiplied by 2.
new ΔV = 2ΔV
Why each choice is right or wrong
- A. This divides instead of multiplying. The factors 2, ⅓ and 3 multiply to 2.
- B. This is what you get if you ignore the changes, or think they cancel. They do not cancel. They multiply to 2.
- C. Correct. The changes multiply: 2 × ⅓ × 3 = 2.
- D. This forgets the one-third for the speed. Twice the length and three times the field would give 6.
Answer: C
Numerical response · outcome 30-B3.9kA metal rod 0.60 m long moves at right angles to a magnetic field of 0.300 T and at right angles to its own length. The potential difference between its ends is 2.70 V. The equation is ΔV = Blv. What is the speed of the rod? Record your answer as a.bc × 10ⁿ m/s. Enter the digits a, b, c, and then n.
Show the worked solution (try the question first)
- Write the equation.
It is given: ΔV = Blv.
ΔV = Blv
- Solve for the speed.
Divide both sides by B and l.
v = ΔV ÷ (Bl)
- Substitute.
Put the bottom in brackets.
v = 2.70 ÷ [(0.300)(0.60)] = 15.0 m/s
- Enter the digits.
Write 15.0 as 1.50 × 10¹. So a, b, c are 1, 5, 0, and n is 1.
record 1 5 0 1
Answer: 15.0 m/s. Record 1 5 0 1.
Multiple choice · outcome 30-B3.9kA strong magnet is dropped down a vertical aluminium tube and falls much more slowly than it does in air. Which statement explains this?
- A. Aluminium is magnetic and attracts the magnet upward.
- B. The air inside the tube is thicker than the air outside it.
- C. Gravity is weaker inside the tube.
- D. The moving magnet induces currents in the tube, and the force on them opposes the motion.
Show the worked solution (try the question first)
- Start with the motion.
The moving magnet makes the aluminium cut across its field. This is the generator effect.
motion → induced currents in the tube
- Find the force.
The currents are in a magnetic field, so they feel a force. There is a matching force on the magnet.
force on the magnet
- Use Lenz’s law.
The force from the induced current opposes the motion. The magnet moves down, so the force is up. That slows the fall.
force up, fall slowed
Why each choice is right or wrong
- A. Aluminium is not magnetic. The force comes from the currents that the moving magnet induces.
- B. The air in the tube is the same as other air. It cannot slow the magnet so much.
- C. Gravity does not change inside a tube. The extra upward force is magnetic.
- D. Correct. Motion induces currents. By Lenz’s law, the force from those currents opposes the motion.
Answer: D