B8 · Electrolytic cells · Completed notes
Download the printable PDF
Goals: Explain how an electrolytic cell uses electrical energy to drive a reaction that is not spontaneous. Identify the anode, cathode, polarity and ion movement, and write half-reactions for molten salts and plating. Compare voltaic and electrolytic cells.
Slide 1 of 8 · Driving a reaction that will not go by itself
Key ideas
E°reaction = E°cathode − E°anode. A positive value means the reaction goes by itself. A negative value means it does not.
A power source can force a reaction that is not spontaneous. A cell that uses electrical energy to do this is an electrolytic cell.
A voltaic cell does the opposite. It turns a spontaneous reaction into electrical energy.
If E°reaction = −1.10 V, the source must supply more than 1.10 V. Give a minimum voltage as a positive number.
Example
Given Cu + Zn²⁺ → Cu²⁺ + Zn, with E°(Zn²⁺/Zn) = −0.76 V and E°(Cu²⁺/Cu) = +0.34 V. Find E°reaction. Does the reaction go by itself? What minimum voltage must a power source exceed to force it?
- Zn²⁺ is reduced (cathode, −0.76 V). Cu is oxidized (anode, +0.34 V).
- E°reaction = E°cathode − E°anode = −0.76 V − (+0.34 V) = −1.10 V
- The value is negative, so the reaction does not go by itself.
- A power source must supply more than 1.10 V.
Try it
Given Cu + Mg²⁺ → Cu²⁺ + Mg, with E°(Mg²⁺/Mg) = −2.37 V and E°(Cu²⁺/Cu) = +0.34 V. Find E°reaction. Does the reaction go by itself? What minimum voltage must a power source exceed to force it?
- Mg²⁺ is reduced (cathode, −2.37 V). Cu is oxidized (anode, +0.34 V).
- E°reaction = −2.37 V − (+0.34 V) = −2.71 V
- The value is negative, so the reaction does not go by itself.
- A power source must supply more than 2.71 V.
Slide 2 of 8 · Anode, cathode and the power source
Key ideas
Oxidation happens at the anode and reduction happens at the cathode, in every cell, voltaic or electrolytic.
In an electrolytic cell, the power source sets the signs. The negative terminal pushes electrons to the cathode, so the cathode is negative.
The electrode joined to the positive terminal hands electrons back to the source. That is oxidation, so it is the anode and it is positive.
Cations move toward the cathode and anions move toward the anode. Electrons travel only in the wires, and ions carry the charge in the liquid.
Example
A power source is joined by wires to two electrodes in a liquid that has ions. Which electrode is the cathode and which is the anode? Which way do cations and anions move, and where do the electrons travel?
- The electrode joined to the negative terminal gains electrons (reduction), so it is the cathode.
- The electrode joined to the positive terminal loses electrons (oxidation), so it is the anode.
- Cations move toward the cathode. Anions move toward the anode.
- Electrons travel only in the wires: from the anode to the positive terminal, and from the negative terminal to the cathode.
Try it
Two inert electrodes dip in molten KBr. Electrode X is joined to the negative terminal of a power source. Name electrode X, name the process at X, and say whether K⁺ moves toward or away from X.
- Electrode X is the cathode, because it is joined to the negative terminal.
- Reduction happens at X.
- K⁺ is a cation, so it moves toward X.
Slide 3 of 8 · A molten salt cell
Key ideas
Molten NaCl has only Na⁺ and Cl⁻ ions and no water, so each electrode has only one ion that can react.
Na⁺ moves to the negative cathode: Na⁺ + e⁻ → Na. Cl⁻ moves to the positive anode: 2Cl⁻ → Cl₂ + 2e⁻.
The anode loses 2 electrons and the cathode half gains 1, so double the cathode half. Cell reaction: 2Na⁺ + 2Cl⁻ → 2Na + Cl₂.
E°reaction = −2.71 − (+1.36) = −4.07 V. E° is never multiplied by a coefficient. The source must supply more than 4.07 V.
Example
Molten sodium chloride, NaCl(l), has two inert electrodes joined to a power source. Given E°(Na⁺/Na) = −2.71 V and E°(Cl₂/Cl⁻) = +1.36 V. Write both half-reactions and the cell reaction, name the product at each electrode, and find E°reaction.
- Cathode (negative): Na⁺ + e⁻ → Na. Sodium metal forms.
- Anode (positive): 2Cl⁻ → Cl₂ + 2e⁻. Chlorine gas forms.
- Double the cathode half: 2Na⁺ + 2e⁻ → 2Na. Overall: 2Na⁺ + 2Cl⁻ → 2Na + Cl₂
- E°reaction = E°cathode − E°anode = −2.71 V − (+1.36 V) = −4.07 V
- The source must supply more than 4.07 V.
Try it
Molten potassium bromide, KBr(l), has two inert electrodes joined to a power source. Given E°(K⁺/K) = −2.93 V and E°(Br₂/Br⁻) = +1.07 V. Write the cell reaction, name the product at each electrode, and find E°reaction.
- Cathode: K⁺ + e⁻ → K. Potassium metal forms.
- Anode: 2Br⁻ → Br₂ + 2e⁻. Bromine forms.
- Double the cathode half. Overall: 2K⁺ + 2Br⁻ → 2K + Br₂
- E°reaction = −2.93 V − (+1.07 V) = −4.00 V
- The source must supply more than 4.00 V.
Slide 4 of 8 · Method: how to describe an electrolytic cell
Key ideas
Step 1. List the ions present. A molten salt has no water.
Step 2. Send cations to the cathode. Reduction happens at the cathode.
Step 3. Send anions to the anode. Oxidation happens at the anode.
Step 4. Write the halves and the overall equation. Match the electrons first.
Step 5. Find E°reaction = E°cathode − E°anode. The source must be larger than its size, and the cathode joins the negative terminal.
Example
Use the method on molten NaCl with inert electrodes and a power source. What forms at each electrode?
- Step 1: Na⁺ and Cl⁻ only. No water.
- Step 2: Na⁺ + e⁻ → Na at the cathode.
- Step 3: 2Cl⁻ → Cl₂ + 2e⁻ at the anode.
- Steps 4 and 5: 2Na⁺ + 2Cl⁻ → 2Na + Cl₂. E°reaction = −2.71 − (+1.36) = −4.07 V, so the source must be above 4.07 V.
Try it
Use the method on molten MgCl₂ with inert electrodes. E°(Mg²⁺/Mg) = −2.37 V and E°(Cl₂/Cl⁻) = +1.36 V. What forms, and what is the minimum voltage?
- Mg²⁺ goes to the cathode: Mg²⁺ + 2e⁻ → Mg. Cl⁻ goes to the anode: 2Cl⁻ → Cl₂ + 2e⁻.
- Overall: Mg²⁺ + 2Cl⁻ → Mg + Cl₂.
- E°reaction = −2.37 − (+1.36) = −3.73 V, so the source must be above 3.73 V.
Slide 5 of 8 · Voltaic and electrolytic cells side by side
Key ideas
The same two half-cells can run either way. In the voltaic Zn / Cu cell, the reaction is spontaneous and E°reaction = +1.10 V.
In the electrolytic cell, a power source forces the reverse reaction, Cu + Zn²⁺ → Cu²⁺ + Zn. Then E°reaction = −1.10 V.
Energy changes from chemical to electrical in a voltaic cell, and from electrical to chemical in an electrolytic cell.
In both cells, oxidation happens at the anode. The anode is negative in a voltaic cell and positive in an electrolytic cell. In a drawing, a voltmeter means voltaic and a power source means electrolytic.
Example
The Zn²⁺/Zn (−0.76 V) and Cu²⁺/Cu (+0.34 V) half-cells run first as a voltaic cell and then as an electrolytic cell. For each, write the overall reaction and E°reaction, and give the sign of the anode.
- Voltaic: Zn + Cu²⁺ → Zn²⁺ + Cu. E°reaction = +0.34 V − (−0.76 V) = +1.10 V. The anode (Zn) is negative.
- Electrolytic: Cu + Zn²⁺ → Cu²⁺ + Zn. E°reaction = −0.76 V − (+0.34 V) = −1.10 V. The anode (Cu) is positive.
Try it
A cell runs a reaction with E°reaction = −0.46 V. Is it a voltaic or an electrolytic cell? Give the energy change, say whether the reaction is spontaneous, and give the sign of the anode.
- It is an electrolytic cell, because a negative E°reaction means the reaction is not spontaneous and needs a power source.
- The energy changes from electrical to chemical.
- The reaction is not spontaneous. The anode is positive.
Slide 6 of 8 · Your turn: molten zinc bromide
Key ideas
Write the ion movement first. Molten ZnBr₂ has Zn²⁺ and Br⁻ ions. Positive ions go to the negative electrode, the cathode. Br⁻ goes to the anode.
Cathode: Zn²⁺ + 2e⁻ → Zn. Anode: 2Br⁻ → Br₂ + 2e⁻.
Both halves move 2 electrons, so they cancel when added. Cell reaction: Zn²⁺ + 2Br⁻ → Zn + Br₂.
E°reaction = −0.76 − 1.07 = −1.83 V. Swapping the electrodes would wrongly give +1.83 V, as if the cell ran by itself.
Example
Molten zinc bromide, ZnBr₂(l), has two inert electrodes joined to a power source. Given E°(Zn²⁺/Zn) = −0.76 V and E°(Br₂/Br⁻) = +1.07 V. Decide the product at each electrode, write the cell reaction and find the minimum voltage.
- Zn²⁺ goes to the cathode and Br⁻ goes to the anode.
- Cathode: Zn²⁺ + 2e⁻ → Zn. Anode: 2Br⁻ → Br₂ + 2e⁻
- Overall: Zn²⁺ + 2Br⁻ → Zn + Br₂. Zn is 1, Br is 2 and charge is 0 on each side.
- E°reaction = E°cathode − E°anode = −0.76 V − (+1.07 V) = −1.83 V
- The source must supply more than 1.83 V.
Try it
Molten copper(II) bromide, CuBr₂(l), has two inert electrodes joined to a power source. Given E°(Cu²⁺/Cu) = +0.34 V and E°(Br₂/Br⁻) = +1.07 V. Decide the product at each electrode, write the cell reaction and find the minimum voltage.
- Cu²⁺ goes to the cathode and Br⁻ goes to the anode.
- Cathode: Cu²⁺ + 2e⁻ → Cu. Anode: 2Br⁻ → Br₂ + 2e⁻
- Overall: Cu²⁺ + 2Br⁻ → Cu + Br₂. Charge is 0 on each side.
- E°reaction = +0.34 V − (+1.07 V) = −0.73 V
- The source must supply more than 0.73 V.
Slide 7 of 8 · Electroplating and refining
Key ideas
To plate an object, make it the cathode. It is joined to the negative terminal, metal ions gain electrons there, and the object gains mass.
In silver plating, the cathode half-reaction is Ag⁺ + e⁻ → Ag. A silver bar as the anode dissolves: Ag → Ag⁺ + e⁻, so the Ag⁺ concentration stays nearly constant.
In copper refining, impure copper is the anode and a sheet of pure copper is the cathode. Cu is oxidized at one and Cu²⁺ is reduced at the other.
Impurities with a more positive E° than Cu²⁺/Cu, such as silver and gold, stay solid. Impurities with a more negative E°, such as zinc, dissolve.
Example
A steel spoon and a bar of silver are placed in silver nitrate solution, AgNO₃(aq), and joined to a power source. How can a thin layer of silver be placed on the spoon? Name the cathode and anode, write both half-reactions and state each mass change.
- Make the spoon the cathode by joining it to the negative terminal. The silver bar is the anode.
- Cathode: Ag⁺ + e⁻ → Ag. Silver deposits on the spoon, so the spoon gains mass.
- Anode: Ag → Ag⁺ + e⁻. The silver bar dissolves, so it loses mass.
- Silver moves from the anode to the spoon, and Ag⁺ stays nearly constant in the solution.
Try it
A metal key is to be plated with nickel. The cell has a nickel bar and nickel(II) sulfate solution, NiSO₄(aq), joined to a power source. Name the cathode, write both half-reactions and state each mass change.
- The key is the cathode, joined to the negative terminal. The nickel bar is the anode.
- Cathode: Ni²⁺ + 2e⁻ → Ni. Nickel deposits on the key, so the key gains mass.
- Anode: Ni → Ni²⁺ + 2e⁻. The nickel bar dissolves, so it loses mass.
Slide 8 of 8 · The same method with two silver electrodes
Key ideas
The same rule works for any metal. At the cathode, Ag⁺ + e⁻ → Ag, so the cathode gains mass. At the anode, Ag → Ag⁺ + e⁻, so the anode loses mass.
Silver moves from one electrode to the other, so the Ag⁺ concentration stays about the same.
Both electrodes use the same half-cell, so E°reaction = +0.80 − (+0.80) = 0.00 V.
Real cells need a small voltage above 0.00 V to beat resistance. That is why plating and refining use little energy.
Example
Two silver electrodes dip in AgNO₃(aq). Electrode 1 is joined to the negative terminal of a power source and electrode 2 to the positive terminal. Given E°(Ag⁺/Ag) = +0.80 V. Name each electrode, give its half-reaction and mass change, and find E°reaction.
- Electrode 1 is the cathode. Ag⁺ + e⁻ → Ag. It gains mass.
- Electrode 2 is the anode. Ag → Ag⁺ + e⁻. It loses mass.
- Both electrodes use the Ag⁺/Ag half-cell: E°reaction = +0.80 V − (+0.80 V) = 0.00 V
Try it
Two copper electrodes dip in CuSO₄(aq) and are joined to a power source. Given E°(Cu²⁺/Cu) = +0.34 V. Write the half-reaction at the cathode and at the anode, and find E°reaction.
- Cathode: Cu²⁺ + 2e⁻ → Cu. The cathode gains mass.
- Anode: Cu → Cu²⁺ + 2e⁻. The anode loses mass.
- E°reaction = +0.34 V − (+0.34 V) = 0.00 V
Practice 1
Given the Data Booklet table values Mg²⁺/Mg at −2.37 V and Zn²⁺/Zn at −0.76 V. A student wants to drive Zn²⁺ + Mg → Zn + Mg²⁺ backwards in an electrolytic cell, so Mg²⁺ + Zn → Mg + Zn²⁺. Find E°reaction for the reaction in the cell and the smallest voltage that must be exceeded.
Mg²⁺ is reduced at the cathode (−2.37 V) and zinc is oxidized at the anode (−0.76 V). E°reaction = −2.37 − (−0.76) = −1.61 V. The applied voltage must be greater than 1.61 V.
Practice 2
In an electrolytic cell with inert electrodes, which electrode is joined to the positive terminal of the power source? Name the process that happens there and the direction in which anions move.
The anode is joined to the positive terminal. Oxidation happens there, and the anions move toward the anode.
Practice 3
Write the half-reactions and the cell reaction for molten NaCl and name the product at each electrode.
Use Method: how to describe an electrolytic cell. Cathode: Na⁺ + e⁻ → Na (sodium metal). Anode: 2Cl⁻ → Cl₂ + 2e⁻ (chlorine gas). Cell reaction: 2Na⁺ + 2Cl⁻ → 2Na + Cl₂.
Practice 4
Given molten ZnBr₂(l) with inert electrodes (Data Booklet table values: E°(Zn²⁺/Zn) = −0.76 V; E°(Br₂/Br⁻) = +1.07 V). Write the half-reaction at each electrode and calculate E°reaction.
Cathode: Zn²⁺ + 2e⁻ → Zn. Anode: 2Br⁻ → Br₂ + 2e⁻. E°reaction = −0.76 − 1.07 = −1.83 V, so the source must supply more than 1.83 V.
Practice 5
A copper bar and a metal key are placed in copper(II) sulfate solution to plate the key with copper. Say which one is the cathode, write its half-reaction and predict the mass change of each.
The key is the cathode: Cu²⁺ + 2e⁻ → Cu. The key gains mass. The copper bar is the anode: Cu → Cu²⁺ + 2e⁻, so it loses mass.
Practice 6
Compare a voltaic cell and an electrolytic cell for the Zn / Cu pair. Give the sign of E°reaction, the energy change and the sign of the anode in each.
Voltaic: E°reaction +1.10 V, chemical to electrical energy, anode negative. Electrolytic: E°reaction −1.10 V for the reaction that is forced, electrical to chemical energy, anode positive.
Practice 7
Challenge: Given molten CaCl₂(l) with inert electrodes (Data Booklet table values: E°(Ca²⁺/Ca) = −2.87 V; E°(Cl₂/Cl⁻) = +1.36 V). Write the half-reaction at each electrode, name each product, and find E°reaction in volts. Then state the least voltage the power source must supply.
Only Ca²⁺ and Cl⁻ are present. Cathode (reduction): Ca²⁺ + 2e⁻ → Ca. Calcium metal forms. Anode (oxidation): 2Cl⁻ → Cl₂ + 2e⁻. Chlorine gas forms. E°reaction = E°cathode − E°anode = −2.87 − (+1.36) = −4.23 V. It is negative, so the reaction does not run by itself. The power source must supply more than 4.23 V. The table values are for standard conditions, so this is a first estimate for a molten salt.
The PDF key follows the slides, with worked answers.