B8 · Electrolytic cells · Notes and practice
Download the printable PDF
Explain how an electrolytic cell uses electrical energy to drive a reaction that is not spontaneous, label its parts, write its reactions and compare it with a voltaic cell.
Open the complete lesson
Type in the blanks; your notes save on this device only. Use the backup controls at the bottom to keep a portable copy. Nothing is submitted.
1. A power source drives the reaction
A reaction that does not go by itself
Look at Cu + Zn²⁺ → Cu²⁺ + Zn. Zn²⁺ is reduced at the cathode (−0.76 V) and copper is oxidized at the anode (+0.34 V).
E°cell = −0.76 − (+0.34) = . A negative value means the reaction is as written, so it will not go by itself.
But a power source can push it, like pushing a ball uphill. A cell that uses energy to drive a reaction that is not spontaneous is an electrolytic cell.
The source must supply more than . We ignore the sign, because the size of the negative value is the minimum push needed.
On the diploma: give a minimum voltage as a positive number. A negative one is a common wrong choice.
Watch: A reaction that is not spontaneous (Tyler DeWitt, “Electrolysis”, 3:58)
Watch: Splitting water needs electrical energy (Alberta Chemistry Teacher, “Chemistry 30 - Predicting redox reaction from species in the reduction table”, 20:04)
Watch: Why the battery must push the electrons (Tyler DeWitt, “Introduction to Electrochemistry”, 13:46)
Anode and cathode
In every cell, happens at the cathode and happens at the anode. Those names come from the chemical change, not from a plus or minus sign.
In an electrolytic cell, the power source sets the signs. A terminal is where a wire joins the source. The negative terminal pushes electrons out, and they arrive at the electrode joined to it.
Electrons arriving means that electrode gains electrons, which is reduction. So the cathode is joined to the terminal and the anode to the terminal.
Cations (positive ions) move toward the . Anions (negative ions) move toward the .
Electrons move only in the . In the liquid, the moving ions carry the charge. Both electrodes sit in one container, so no salt bridge is needed. In a drawing, a power source in the wire means electrolytic, and a voltmeter means voltaic.
On the diploma: a diagram may show only the power source. Label the terminals first, then the electrodes. The wrong option usually swaps the two electrodes.
Watch: Anode and cathode in an electrolytic cell (Tyler DeWitt, “Electrolysis”, 8:02)
Watch: A way to remember anode and cathode (Tyler DeWitt, “Introduction to Electrochemistry”, 10:44)
Electrolytic cell for molten sodium chloride. Give the electrode names, the source terminal each joins, the reactions and the minimum voltage.2. Molten salts
Molten sodium chloride
Molten NaCl is the ionic solid heated until it melts, so its ions can move. It has only Na⁺ and Cl⁻ ions and no water.
Na⁺ is attracted to the negative and gains one electron: Na⁺ + e⁻ → .
Cl⁻ goes to the positive anode. Cl₂ has two atoms, so two chloride ions each give up one electron: 2Cl⁻ → + 2e⁻.
The anode gives 2 electrons and the cathode takes only 1, so double the cathode half. The cell reaction is 2Na⁺ + 2Cl⁻ → .
E°cell = −2.71 − (+1.36) = , so the source must supply more than . We do not double E° when we double a half-reaction.
On the diploma: list the ions first, then send the cation to the cathode. Doubling E° with the half-reaction is a common wrong choice.
Watch: Splitting sodium chloride (Tyler DeWitt, “Electrolysis”, 0:46)
Watch: A battery forces the reaction (Tyler DeWitt, “Electrolysis”, 4:46)
Watch: Why the salt must be molten (Tyler DeWitt, “Electrolysis”, 7:10)
Watch: The two half-reactions (Tyler DeWitt, “Electrolysis”, 11:56)
Watch: The final equation (Tyler DeWitt, “Electrolysis”, 14:19)
Molten zinc bromide
ZnBr₂(l) has only Zn²⁺ and Br⁻. Zn²⁺ goes to the : Zn²⁺ + 2e⁻ → Zn. Br⁻ goes to the : 2Br⁻ → Br₂ + 2e⁻.
Both halves move two electrons, so they cancel when we add them. The cell reaction is Zn²⁺ + 2Br⁻ → .
E°cell = −0.76 − (+1.07) = . A negative value shows that a power is needed, one that supplies more than 1.83 V.
On the diploma: reporting +1.83 V would suggest the cell runs by itself. Check the electrode order before you subtract, and give the sign.
3. Compare cells, plating and refining
Side by side
The same two half-cells can run either way. In the Zn / Cu voltaic cell, zinc is oxidized and E°cell is +1.10 V. In the electrolytic cell, copper is oxidized and E°cell is −1.10 V for the forced reaction.
Voltaic cell: energy to electrical energy, E°cell , anode . It needs a or porous barrier.
Electrolytic cell: electrical energy to energy, E°cell for the forced reaction , anode . It need a salt bridge.
The voltaic anode is negative because that cell makes electrons there. The electrolytic anode is positive because it is joined to the positive terminal.
On the diploma: many wrong choices copy the voltaic sign onto an electrolytic cell. Check which cell type the question describes.
Watch: Electrolytic cell versus voltaic cell (Tyler DeWitt, “Introduction to Electrochemistry”, 11:30)
Plating and refining
To plate a spoon with silver, make the spoon the . Reduction deposits metal there: Ag⁺ + e⁻ → , so the spoon gains mass.
A silver anode mass as Ag → Ag⁺ + e⁻. It replaces the Ag⁺ the cathode used up, so the ion concentration stays nearly constant. A carbon anode would not dissolve.
To refine copper, impure copper is the anode and a thin pure sheet is the cathode. Pure metal builds up on the . Impurities above copper on the table, like silver and gold, fall as solid. Those below it dissolve.
Two electrodes of the same metal in its own ion give E°cell = , because the same half-reaction is reversed at the anode. Only a small voltage is needed, plus a little extra to beat resistance.
On the diploma: the electrode that gains mass is where ions are reduced, the cathode. Same metal at both electrodes means E°cell = 0.00 V.
Watch: Plating a copper ring with silver (Tyler DeWitt, “Electroplating”, 1:30)
Watch: Which terminal the object connects to (Tyler DeWitt, “Electroplating”, 3:00)
Watch: Half-reaction at the ring (Tyler DeWitt, “Electroplating Part 2”, 1:27)
Watch: Half-reaction at the silver (Tyler DeWitt, “Electroplating Part 2”, 2:36)
Watch: Anode and cathode in electroplating (Tyler DeWitt, “Electroplating Part 2”, 6:23)
Use the diagram response box for labels and arrows in words, or draw on the printable PDF.
Answer the 12 core practice problems online · Completed notes and worked key
B8-P01
Given Ni²⁺ + 2e⁻ → Ni (−0.26 V) and Cu²⁺ + 2e⁻ → Cu (+0.34 V). A power source is used to drive Cu + Ni²⁺ → Cu²⁺ + Ni. Calculate E°cell and state the smallest voltage that the source must exceed.
Response: ____________________
B8-P02
In an electrolytic cell, which electrode is joined to the negative terminal of the power source? Name the process there and give the direction in which cations move.
Response: ____________________
B8-P03
Explain why electrons do not travel through the electrolyte, and why an electrolytic cell does not need a salt bridge.
Response: ____________________
B8-P04
Write the half-reactions, the cell reaction and the product at each electrode for the electrolysis of molten NaCl.
Response: ____________________
B8-P05
Given molten ZnBr₂(l) with inert electrodes (Zn²⁺/Zn −0.76 V; Br₂/Br⁻ +1.07 V). Write the cell reaction and calculate E°cell.
Response: ____________________
B8-P06
Given molten MgCl₂ with inert electrodes (Mg²⁺/Mg −2.37 V; Cl₂/Cl⁻ +1.36 V). Write the cell reaction and calculate the smallest voltage that the source must exceed.
Response: ____________________
B8-P07
Compare a voltaic cell and an electrolytic cell for the Zn / Cu pair. Use the energy change, the sign of the cell value for the reaction that runs, and the sign of the anode.
Response: ____________________
B8-P08
A student says the anode in an electrolytic cell is negative because it is negative in a voltaic cell. Explain the error.
Response: ____________________
B8-P09
A silver spoon is plated in AgNO₃(aq) with a silver bar. Say which is the cathode, write the half-reaction at each electrode and predict the mass change of each.
Response: ____________________
B8-P10
Describe a cell for refining impure copper and name the electrode that gains mass.
Response: ____________________
B8-P11
Silver electrodes are placed in silver nitrate solution and connected to a power source. Calculate E°cell for the reaction in this cell and say how much voltage is needed in principle.
Response: ____________________
B8-P12
A student says that a negative E°cell means a reaction cannot happen at all. Use the idea of an electrolytic cell to correct this.
Response: ____________________