All lessons

Potential difference: energy per charge

Complete reading and printing route. Attempt each question before reading its feedback. All diagram stages are included below.

After the lesson: Investigate and connect: a short investigation, a data step and a real-world link.

Work that stores energy between plates

Watch this part in the video

On a small screen, scroll sideways to read the labels.

In B4, a field pushed a charge. Moving a charge against that push takes work.
Symbols in this lesson:
q = charge (C) · ΔE = energy change (J) · ΔV = potential difference (V)
Ep = electric potential energy · Ek = kinetic energy · m = mass (kg) · v = speed (m/s)
e = size of one electron’s charge · eV = electron volt, a unit of energy
Givens from the setup: a battery charges two parallel plates, top plate negative and bottom plate positive. A small particle with positive charge q = 4.0 × 10⁻¹⁷ C rests against the top plate at A. Gravity is too small to matter. Tweezers carry it to B at constant speed.

−+−+−+−+−+−+battery+ABmoved at constant speed

Pushing a charge where it does not want to go

Opposite charges attract. A positive particle against the negative plate is where it wants to be.

  • Call its electric potential energy (Ep) zero there. A ball at a hill’s bottom is the same.
  • Carrying it to B takes a push, because the plates pull and push it back.
  • Our push does work: a force moves the particle, so energy is transferred. The speed is constant, so no kinetic energy is gained.
  • All the work is stored: ΔEp = 6.0 × 10⁻¹⁶ J. Δ means “change in”.

Givens: the particle with q = 4.0 × 10⁻¹⁷ C has been carried to B, where it has gained 6.0 × 10⁻¹⁶ J of electric potential energy. It is released from rest and gravity is too small to matter. Question: which way does it move, and how much kinetic energy does it have when it reaches the top plate?

−+−+−+−+−+−+battery+BA

Release the particle

The particle is released at B. Which way does the force point?

  • The positive plate pushes it away. The negative plate pulls it in.
  • As Ep falls, kinetic energy (Ek) rises. Nothing else takes a share.

Answer with a direction, a number and a reason.

Diploma: a “predict” or “explain” answer needs a law or principle as the reason.

Starting point if needed

The positive particle is repelled by the positive plate and attracted to the negative plate.

Compare after your attempt

The particle moves up toward the negative top plate. Like charges repel and unlike charges attract, so the force on it at B points upward.

As it moves, electric potential energy turns into kinetic energy. With no other losses, all 6.0 × 10⁻¹⁶ J becomes kinetic energy by the time it reaches the top plate.

Potential difference: energy per charge

Watch this part in the video

On a small screen, scroll sideways to read the labels.

On slide 1, the particle stored 6.0 × 10⁻¹⁶ J. A bigger charge would store more.
Givens: q = 4.0 × 10⁻¹⁷ C is moved from A to B between the plates, and ΔE = 6.0 × 10⁻¹⁶ J is stored. Find the electric potential difference between A and B. The same plates are then used with a charge three times as large.

−+−+−+−+−+−+battery+ΔV = ΔE / q(J/C)

Divide out the charge

So divide the energy by the charge. This gives one number for the plates.

  • Formula: ΔV = ΔE ÷ q.
  • ΔE is the energy change, ΔEp (J).
  • q is the size of the charge (C).
  • ΔV = (6.0 × 10⁻¹⁶ J) ÷ (4.0 × 10⁻¹⁷ C) = 15 J/C.
  • Triple the charge. The energy triples. ΔV is still 15 J/C.
  • So ΔV belongs to the plates, not the particle.
  • Use the size of q. Toward the plate that attracts it, it gains kinetic energy.

Givens: other plates. A charge q = 6.0 × 10⁻¹⁸ C stores 1.8 × 10⁻¹⁶ J when it is moved from A to B. Question: find the potential difference between A and B, then find the energy stored when a charge of 1.5 × 10⁻¹⁷ C is moved between the same two points.

−+−+−+−+−+−+battery+

Find ΔV, then the energy for a different charge

Use ΔV = ΔE ÷ q on new plates. If you know two of the three values, you can find the third.

  1. Part one: find ΔV. Put the unit on it.
  2. Part two: rearrange to ΔE = qΔV. Use the new charge.
  3. The plates are the same, so ΔV is the same.
  4. Check the powers of ten. The charges are tiny.

A wrong part one carries into part two.

Starting point if needed

Find ΔV first. Then rearrange ΔV = ΔE/q to ΔE = qΔV for the new charge.

Compare after your attempt

ΔV = ΔE ÷ q = (1.8 × 10⁻¹⁶ J) ÷ (6.0 × 10⁻¹⁸ C) = 30 J/C.

For the other charge, ΔE = qΔV = (1.5 × 10⁻¹⁷ C)(30 J/C) = 4.5 × 10⁻¹⁶ J.

New situation: the same plates are used to move several different charges from A to B, and the energy stored is graphed against the charge. The line passes through C = (2.0 × 10⁻¹⁸ C, 0.60 × 10⁻¹⁶ J) and D = (8.0 × 10⁻¹⁸ C, 2.40 × 10⁻¹⁶ J). Question: what does the slope of this line represent, and what is its value?

02468100.00.51.01.52.02.53.0energy gained ΔE (×10⁻¹⁶ J)charge q (×10⁻¹⁸ C)C (2.0, 0.60)D (8.0, 2.40)

Changed representation: read ΔV from a graph

Match ΔE = qΔV to y = mx, as in B5. The graph shows energy stored against charge moved.

  1. What is on the vertical axis? What is on the horizontal axis?
  2. The number that multiplies the horizontal value is the slope.
  3. Find the slope from points C and D: rise ÷ run, with units.
  4. Should the line pass through the origin? Say why.

Diploma: “what does the slope represent” needs its meaning and value.

Compare after your attempt

Match ΔE = qΔV to y = mx. ΔE is the vertical quantity, q is the horizontal quantity, and the slope is the potential difference ΔV.

Slope = (2.40 × 10⁻¹⁶ J − 0.60 × 10⁻¹⁶ J) ÷ (8.0 × 10⁻¹⁸ C − 2.0 × 10⁻¹⁸ C) = 1.8 × 10⁻¹⁶ ÷ (6.0 × 10⁻¹⁸) = 30 J/C. The line passes through the origin because zero charge stores zero energy.

Method: how to solve an energy-per-charge problem

On a small screen, scroll sideways to read the labels.

These are the steps you used on slide 2.
Use this method whenever a question gives two of the three quantities energy, charge and potential difference and asks for the third.

1Name the unknown2Write the equation3Put in the sizes4Calculate with units

Method: how to solve an energy-per-charge problem

  1. Name the unknown. Is it ΔE, q or ΔV? Write it first.
  2. Write the equation for it. ΔV = ΔE/q, ΔE = qΔV or q = ΔE/ΔV.
  3. Put in the sizes. Charge in coulombs, energy in joules. Toward the plate that attracts it, it gains kinetic energy.
  4. Calculate with units. J/C is the volt. Keep the full value until the end.

Check: Does the unit work out? Does a bigger charge store more energy?

Used again in: the volt and battery questions in slide 4, the electron-gun slides in slide 5, and the plate problems in B7 and B8.

Givens (the question in slide 2): a charge of 6.0 × 10⁻¹⁸ C stores 1.8 × 10⁻¹⁶ J when it is moved from A to B. A charge of 1.5 × 10⁻¹⁷ C is then moved between the same two points.

1Name the unknown2Write the equation3Put in the sizes4Calculate with units

Run-through: ΔV first, then the energy for a new charge

The question from slide 2, step by step: a charge of 6.0 × 10⁻¹⁸ C stores 1.8 × 10⁻¹⁶ J. A charge of 1.5 × 10⁻¹⁷ C is then moved between the same two points.

  1. Step 1Part one: ΔV is the unknown. Part two: ΔE is the unknown.
  2. Step 2ΔV = ΔE ÷ q. For part two, rearrange to ΔE = qΔV.
  3. Step 3ΔV = (1.8 × 10⁻¹⁶ J) ÷ (6.0 × 10⁻¹⁸ C). Then ΔE = (1.5 × 10⁻¹⁷ C) × ΔV, using the sizes of the charges.
  4. Step 4ΔV = 30 J/C, so ΔE = (1.5 × 10⁻¹⁷)(30) = 4.5 × 10⁻¹⁶ J. The unit J/C is the volt, so ΔV = 30 V.

The volt: one joule per coulomb

Watch this part in the video

On a small screen, scroll sideways to read the labels.

Slide 2 gave ΔV in joules per coulomb. That unit has a shorter name.
Givens: a battery is labelled 9.0 V and is connected to a heating coil. A charge of 4.0 C flows through the coil. Find the energy delivered.

+−9.0 V battery1 V = 1 J / 1 CΔE = q ΔV

Name the unit

The name is the volt.

  • One volt is one joule per coulomb: 1 V = 1 J/C.
  • “Voltage” means potential difference. A 9.0 V label means ΔV = 9.0 V.
  • Unlike the field E, ΔV has no direction.
  • The battery gives 9.0 J to each coulomb.
  • ΔE = qΔV = (4.0 C)(9.0 V) = 36 J.
  • A battery supplies energy for charge already in the wires. It does not store charge to hand out.

Givens: a 6.0 V battery is connected to a lamp. Question: how much energy is delivered when 2.5 C of charge passes through the lamp, and how much charge must pass to deliver 90 J?

6.0 V battery → lampa) charge 2.5 C passes: energy = ?b) energy 90 J delivered: charge = ?

Energy from charge, and charge from energy

A volt means one joule per coulomb. So you can go both ways.

  1. Part one: put the charge and voltage into ΔE = qΔV.
  2. Part two: rearrange to q = ΔE ÷ ΔV.
  3. Keep units: coulombs times volts gives joules.
  4. Say which form you used for each part.

Quick check: 6.0 V gives 6.0 J per coulomb. So 90 J needs many coulombs.

Diploma: match the formula to the unknown. Watch the rearranging.

Compare after your attempt

ΔE = qΔV = (2.5 C)(6.0 V) = 15 J.

q = ΔE ÷ ΔV = 90 J ÷ 6.0 V = 15 C.

A charge accelerated through a voltage

Watch this part in the video

On a small screen, scroll sideways to read the labels.

Slide 4 found the energy a voltage gives a charge. That energy can become speed.
Givens: an electron starts from rest at the negative plate of an electron gun and is accelerated through ΔV = 1.80 × 10³ V. The data sheet gives q = 1.60 × 10⁻¹⁹ C and m = 9.11 × 10⁻³¹ kg. Find the speed when it reaches the positive plate.

−+−starts from restvoltage across the gap: 1.80 × 10³ V

From rest: the energy becomes speed

An electron gun uses a voltage to give electrons speed.

  • ΔE = qΔV. Kinetic energy is Ek = ½mv². Small i means initial. Small f means final.
  • Energy is conserved: lost Ep becomes Ek, so qΔV = ½mvf² − ½mvi².
  • “From rest” means vi = 0, so that term drops out.
  • qΔV = (1.60 × 10⁻¹⁹ C)(1.80 × 10³ V) = 2.88 × 10⁻¹⁶ J.
  • Then v = √(2 × Ek ÷ m).
  • = √(2 × 2.88 × 10⁻¹⁶ ÷ (9.11 × 10⁻³¹)) = 2.51 × 10⁷ m/s.

Givens: an electron enters the gap at vi = 1.50 × 10⁷ m/s and is accelerated through ΔV = 6.00 × 10² V. Find its final speed.

initial Ekgained qΔVfinal EkAn electron enters the gap already moving.

Already moving: add to the energy it has

This electron is already moving. Think start, gain, total.

  • Start: ½mvi² = ½(9.11 × 10⁻³¹)(1.50 × 10⁷)² = 1.024 × 10⁻¹⁶ J.
  • Gain: qΔV = (1.60 × 10⁻¹⁹)(6.00 × 10²) = 9.600 × 10⁻¹⁷ J.
  • Total: 1.984 × 10⁻¹⁶ J.
  • Then vf = √(2 × Ek ÷ m).
  • = √(2 × 1.984 × 10⁻¹⁶ ÷ (9.11 × 10⁻³¹)) = 2.09 × 10⁷ m/s.

Check: it must end faster than 1.50 × 10⁷ m/s. Leaving out the start gives 1.45 × 10⁷ m/s: too slow.

Givens: an alpha particle (mass 6.65 × 10⁻²⁷ kg, charge 3.20 × 10⁻¹⁹ C) starts from rest and is accelerated through a potential difference of 2.00 × 10⁴ V. Question: find its final speed.

+−+alpha, from restvoltage across the gap: 2.00 × 10⁴ V

A heavier particle, from rest

An alpha particle is a helium nucleus: 2 protons and 2 neutrons, charge +2e. The method is the same. Use its own numbers, not the electron’s.

  1. Find the energy gained. Use the alpha particle’s own charge.
  2. It starts from rest, so that is all its kinetic energy.
  3. Solve ½mv² for v: double the energy, divide by mass, take the square root.
  4. Is the speed sensible? A heavy particle ends slower than an electron.

Diploma: write “from rest, so vi = 0” so the marker sees it.

Starting point if needed

Start from qΔV = ½mv², using the alpha particle’s own charge.

Compare after your attempt

qΔV = (3.20 × 10⁻¹⁹ C)(2.00 × 10⁴ V) = 6.40 × 10⁻¹⁵ J. The particle starts from rest, so this is its final kinetic energy.

v = √(2Ek/m) = √(2 × 6.40 × 10⁻¹⁵ ÷ (6.65 × 10⁻²⁷)) = 1.39 × 10⁶ m/s.

New situation: a proton (mass 1.67 × 10⁻²⁷ kg, charge 1.60 × 10⁻¹⁹ C) enters the gap at 3.0 × 10⁵ m/s and is accelerated through 5.00 × 10² V. Question: find its final speed, and say whether the answer passes the reasonableness check.

+−+proton, already movingvoltage across the gap: 5.00 × 10² V

Changed particle and starting speed

A proton enters the gap already moving. Use the moving-electron steps.

  1. Work out the energy it has.
  2. Work out the energy it gains.
  3. Add them, then find the speed.
  4. Use the proton’s own mass. It is much bigger than the electron’s.

Check: a particle sped up by the voltage must end faster. Say which check you used.

Compare after your attempt

Initial kinetic energy: ½(1.67 × 10⁻²⁷ kg)(3.0 × 10⁵ m/s)² = 7.5 × 10⁻¹⁷ J. Energy gained: qΔV = (1.60 × 10⁻¹⁹ C)(5.00 × 10² V) = 8.0 × 10⁻¹⁷ J.

Final kinetic energy = 1.55 × 10⁻¹⁶ J, so v = √(2 × 1.55 × 10⁻¹⁶ ÷ (1.67 × 10⁻²⁷)) = 4.31 × 10⁵ m/s. This is greater than the starting speed, so the check is passed.

Method: how to find the speed of a charge accelerated through a voltage

On a small screen, scroll sideways to read the labels.

These are the steps you used on slide 5.
Use this method whenever a charged particle crosses a voltage and the question asks for its final speed.

1Write the energy rule2Find the gain3Find the start4Add, then solve

Method: how to find the speed of a charge accelerated through a voltage

  1. Write the energy rule. qΔV = ½mvf² − ½mvi². The energy from the voltage becomes kinetic energy.
  2. Find the energy gained. qΔV: charge in coulombs, voltage in volts. The answer is in joules.
  3. Find the starting energy. “From rest” means ½mvi² = 0. Already moving? Work out ½mvi² with its own mass.
  4. Add, then solve for v. Final Ek = start + gain. v = √(2 × Ek ÷ m). Keep the full value.

Check: The unit must be m/s. A sped-up particle must end faster than it began.

Used again in: the alpha particle and proton questions in this lesson, and the plate and electron-gun problems in B8 and B12.

Givens (the electron gun in slide 5): an electron starts from rest and crosses a gap with a voltage of 1.80 × 10³ V. Its charge is 1.60 × 10⁻¹⁹ C and its mass is 9.11 × 10⁻³¹ kg.

1Write the energy rule2Find the gain3Find the start4Add, then solve

Run-through: an electron from rest through 1.80 × 10³ V

The electron gun from slide 5, step by step: an electron starts from rest and crosses a gap with a voltage of 1.80 × 10³ V.

  1. Step 1qΔV = ½mvf² − ½mvi². For the electron, q = 1.60 × 10⁻¹⁹ C and m = 9.11 × 10⁻³¹ kg.
  2. Step 2qΔV = (1.60 × 10⁻¹⁹ C)(1.80 × 10³ V) = 2.88 × 10⁻¹⁶ J.
  3. Step 3The electron starts from rest, so the starting energy is 0.
  4. Step 4Final Ek = 2.88 × 10⁻¹⁶ J. v = √(2 × 2.88 × 10⁻¹⁶ ÷ (9.11 × 10⁻³¹)) = 2.5145… × 10⁷ m/s, so v = 2.51 × 10⁷ m/s.

The electron volt

Watch this part in the video

On a small screen, scroll sideways to read the labels.

On slide 5, one electron gained 2.88 × 10⁻¹⁶ J. Numbers that small are awkward.
Givens: the data sheet gives 1 eV = 1.60 × 10⁻¹⁹ J. An electron is accelerated from rest through 24.0 V. An alpha particle (charge 3.20 × 10⁻¹⁹ C) is accelerated from rest through 15.0 V. Find the energy each gains in electron volts.

1 eV = 1.60 × 10⁻¹⁹ JJ → eV : divide by 1.60 × 10⁻¹⁹ J/eVeV → J : multiply by 1.60 × 10⁻¹⁹ J/eVan electron through 1 V gains 1 eV

A unit of energy sized for particles

So we use a smaller unit of energy.

  • The electron volt (eV) is a unit of energy, not voltage.
  • One eV is the energy an electron gains through one volt: 1.60 × 10⁻¹⁹ J.
  • An electron through 24.0 V gains 24.0 eV.
  • An alpha particle has twice the charge, so it gains 30.0 eV through 15.0 V.
  • In joules: (3.20 × 10⁻¹⁹)(15.0) = 4.80 × 10⁻¹⁸ J.

ΔE = qΔV still needs joules, coulombs and volts.

Givens: an alpha particle (charge 3.20 × 10⁻¹⁹ C) is accelerated from rest through 45.0 V. Question: find the kinetic energy it gains, first in electron volts and then in joules.

alpha particle, from rest, through 45.0 Va) kinetic energy gained in eV = ?b) kinetic energy gained in J = ?

Energy in eV and in J

An electron volt is the energy for one electron’s charge through one volt. Use that for the alpha particle.

  1. Its charge is how many times an electron’s?
  2. eV answer: multiply that number by the voltage.
  3. Joule answer: convert with the data sheet value.
  4. Check with qΔV in coulombs. The two routes must agree.
Compare after your attempt

The alpha particle has charge 2e, so each volt gives it 2 eV: 2 × 45.0 V = 90.0 eV.

In joules: 90.0 eV × 1.60 × 10⁻¹⁹ J/eV = 1.44 × 10⁻¹⁷ J. This matches qΔV = (3.20 × 10⁻¹⁹ C)(45.0 V) = 1.44 × 10⁻¹⁷ J.

Givens: an electron enters the gap at 1.0 × 10⁶ m/s and is accelerated through 80.0 V. Question: find its final kinetic energy in electron volts. Record the answer as a.bc × 10ⁿ eV.

electron enters at 1.0 × 10⁶ m/saccelerated through 80.0 Vfinal kinetic energy: ___ eVrecord as a.bc × 10ⁿ

Diploma-style numerical response

This is a diploma-style numerical response. An electron enters moving and is sped up through 80.0 V. Think start plus gain.

  1. The gain is easy in eV: the charge is one electron’s worth.
  2. The start needs ½mv² in joules.
  3. Convert it to eV with the data sheet value.
  4. Add the two. Round only at the end.

Diploma: write a.bc × 10ⁿ with the unit eV. Round half up.

Compare after your attempt

Gain: an electron through 80.0 V gains 80.0 eV. Initial energy: ½mv² = ½(9.11 × 10⁻³¹ kg)(1.0 × 10⁶ m/s)² = 4.555 × 10⁻¹⁹ J, which is 4.555 × 10⁻¹⁹ ÷ (1.60 × 10⁻¹⁹) = 2.847 eV.

Final energy = 80.0 eV + 2.847 eV = 82.847 eV, which rounds to 82.8 eV. Record 8.28 × 10¹ eV.

Practice question

A charge of 5.0 × 10⁻¹⁸ C is moved between two plates, and 1.5 × 10⁻¹⁶ J of energy is stored. Find the potential difference between the two points, and the energy stored when a charge of 2.0 × 10⁻¹⁷ C is moved between the same points.

Hint

Find ΔV = ΔE ÷ q first. The same ΔV gives the energy for the second charge.

Compare after your attempt

ΔV = ΔE/q = 1.5 × 10⁻¹⁶ ÷ (5.0 × 10⁻¹⁸) = 30 J/C. For the second charge, ΔE = qΔV = (2.0 × 10⁻¹⁷)(30) = 6.0 × 10⁻¹⁶ J.

Practice question

A 12 V battery is connected to a motor. How much energy is delivered when 8.0 C of charge passes through the motor?

Hint

A volt is a joule per coulomb, so use ΔE = qΔV.

Compare after your attempt

ΔE = qΔV = (8.0 C)(12 V) = 96 J.

Practice question

An electron starts from rest and is accelerated through 3.50 × 10³ V. Find its final speed.

Hint

It starts from rest, so qΔV = ½mv². Solve for v.

Compare after your attempt

qΔV = (1.60 × 10⁻¹⁹)(3.50 × 10³) = 5.60 × 10⁻¹⁶ J. v = √(2 × 5.60 × 10⁻¹⁶ ÷ (9.11 × 10⁻³¹)) = 3.51 × 10⁷ m/s.

Practice question

An electron enters a gap moving at 2.0 × 10⁷ m/s and is accelerated through 4.00 × 10² V. Find its final speed, and say how you know the answer is reasonable.

Hint

Find the starting kinetic energy. Add qΔV. Then solve ½mv² for v.

Compare after your attempt

Initial Ek = ½(9.11 × 10⁻³¹)(2.0 × 10⁷)² = 1.82 × 10⁻¹⁶ J. Gain = (1.60 × 10⁻¹⁹)(4.00 × 10²) = 6.4 × 10⁻¹⁷ J. Final Ek = 2.46 × 10⁻¹⁶ J, so v = √(2 × 2.46 × 10⁻¹⁶ ÷ (9.11 × 10⁻³¹)) = 2.32 × 10⁷ m/s. It is greater than the starting speed, as it must be.

Practice question

A particle with charge 4.80 × 10⁻¹⁹ C is accelerated from rest through 25.0 V. Find the kinetic energy it gains in electron volts and in joules.

Hint

How many times e is the charge? Each volt gives that many electron volts.

Compare after your attempt

The charge is 3e, so the energy gained is 3 × 25.0 = 75.0 eV. In joules, 75.0 × 1.60 × 10⁻¹⁹ = 1.20 × 10⁻¹⁷ J.

Challenge question

Challenge: An electron and a proton each start from rest and are accelerated through the same potential difference. How many times faster is the electron at the end? Use m(electron) = 9.11 × 10⁻³¹ kg and m(proton) = 1.67 × 10⁻²⁷ kg.

Hint

Write v = √(2qΔV ÷ m) for each particle, then divide one by the other. See what cancels.

Compare after your attempt

Each gains the same energy, because the charges have the same size: qΔV = ½mv², so v = √(2qΔV ÷ m). The q and ΔV are the same for both, so the ratio of speeds is √(m(proton) ÷ m(electron)) = √(1.67 × 10⁻²⁷ ÷ (9.11 × 10⁻³¹)) = 42.8. The electron is 42.8 times faster, whatever the voltage is.