All lessons

Reading straight-line graphs: slope, intercept and constants

Complete reading and printing route. Attempt each question before reading its feedback. All diagram stages are included below.

After the lesson: Investigate and connect: a short investigation, a data step and a real-world link.

Two variables and a line of best fit

Watch this part in the video

On a small screen, scroll sideways to read the labels.

B2 to B4 gave laws as equations. A graph of real data can test them.
Symbols in this lesson:
y = mx + b: m = slope · b = intercept on the vertical axis · F = force (N) · x = extension (m)
k = spring constant (N/m) at first, then Coulomb’s constant (N·m²/C²) · r = distance (m)
E = electric field strength, in N/C (newtons per coulomb) · Q = source charge (C) · μC = microcoulomb, 10⁻⁶ C
Givens from the experiment: a student pulls one spring to chosen stretches, measured on a ruler, and reads the force on a force meter each time. The spring, the ruler and the room stay the same. Six trials are plotted.

0246810120.01.02.03.04.0force F (N)extension x (×10⁻² m)

Change one thing, measure one thing

A fair test changes one thing and measures one thing.

  • Manipulated variable: the one you change. Here, the stretch in metres.
  • Responding variable: the one you measure. Here, the force in newtons.
  • Held fixed: everything else, like the spring and the ruler.

Points never fall exactly on a line. Every reading has a small error.

Same six data points. A line of best fit has been drawn through the trend. Points A and B are two places on the line, not data points.

0246810120.01.02.03.04.0force F (N)extension x (×10⁻² m)AB

Draw the line, then read from the line

A line of best fit follows the trend. About as many points sit above as below. It averages out the errors.

  1. Read values from the line, never from single data points. A single point carries its own error.
  2. Choose two points far apart on the line. A small triangle makes the error a big share of the answer.

Givens: a student changes the source charge Q and measures the electric field strength E with a probe. The probe stays 0.500 m from the source in air. Question: which quantity is manipulated, which is responding, which quantity is held fixed, and which one goes on the horizontal axis?

fixed distance r = 0.500 m+source Q (changed)probe: reads E

Name the variables and the axes

Think back to the spring. There you changed the stretch and measured the force. Now do the same for Q and E.

  1. What do you change? That is the manipulated variable. It goes on the horizontal axis.
  2. What do you measure? That is the responding variable. It goes on the vertical axis.
  3. Everything else stays the same.

Diploma: name the manipulated, responding and fixed variables.

Starting point if needed

The horizontal axis holds the quantity you chose to change.

Compare after your attempt

Manipulated: source charge Q (horizontal axis). Responding: electric field strength E (vertical axis). Fixed: the distance r = 0.500 m, and the constant k, which is a fixed number of nature rather than something an experimenter adjusts.

If r also changed, E would depend on two things at once and the graph could not show how E depends on Q alone.

Find the slope from the line

Watch this part in the video

On a small screen, scroll sideways to read the labels.

Slide 1 drew a line of best fit. Now find its slope.
Givens from the graph: a straight line of best fit for spring force F against extension x. Points A and B lie on the line. Gridlines are every 2 × 10⁻² m across and every 0.50 N up.

0246810120.01.02.03.04.0force F (N)extension x (×10⁻² m)ABrunrise

Rise over run on the line

Slope = rise ÷ run. Rise is how far the line goes up between two points. Run is how far it goes across.

  1. Take B minus A for the rise.
  2. Take B minus A for the run. Use the same order.
  3. The unit is the vertical unit ÷ the horizontal unit. Here: force F in N, extension x in m.

The gridlines are every 2 × 10⁻² m across and every 0.50 N up.

Givens from the graph: A at (2.0 × 10⁻² m, 1.00 N) and B at (10.0 × 10⁻² m, 3.00 N). The horizontal axis is labelled in units of 10⁻² m. Find the slope.

0246810120.01.02.03.04.0force F (N)extension x (×10⁻² m)A (2.0, 1.00)B (10.0, 3.00)run = 8.0 × 10⁻² mrise = 2.00 N

Numbers, units and powers of ten

Point A is (2.0 × 10⁻² m, 1.00 N). Point B is (10.0 × 10⁻² m, 3.00 N). F_B is the force at B. x_A is the extension at A.

  1. Rise = F_B − F_A = 3.00 − 1.00 = 2.00 N.
  2. Run = x_B − x_A = (10.0 − 2.0) × 10⁻² m = 0.080 m.
  3. Slope = 2.00 ÷ 0.080 = 25.0 N/m.

A slope of 250 or 0.25 means the power of ten was lost.

Keep full values on your calculator. Round once, to 3 digits.

Givens: a different spring’s line of best fit passes through C = (3.0 × 10⁻² m, 1.40 N) and D = (9.0 × 10⁻² m, 3.80 N). Question: find the slope of the line, including its unit. Show the rise, the run and the unit check.

0246810120.01.02.03.04.05.06.0force F (N)extension x (×10⁻² m)CD

Find a slope with units

This is another spring. Its line passes through C and D. Use the same method.

  1. Rise: subtract C from D for the force.
  2. Run: subtract C from D for the extension. Keep the power of ten.
  3. Convert the run to metres. The unit comes out as N/m.

If the number looks too big or too small, check the powers of ten.

Diploma: show the rise, the run and the unit check.

Starting point if needed

Subtract C from D for both the force and the extension.

Compare after your attempt

Rise = 3.80 N − 1.40 N = 2.40 N. Run = (9.0 − 3.0) × 10⁻² m = 6.0 × 10⁻² m = 0.060 m.

Slope = 2.40 N ÷ 0.060 m = 40.0 N/m. The unit is newtons per metre, vertical over horizontal.

Match the physics equation to y = mx + b

Watch this part in the video

On a small screen, scroll sideways to read the labels.

Slide 2 gave a slope of 25.0 N/m. Now find what that number means.
Givens: the straight-line equation y = mx + b and Hooke’s law F = kx, where k is the spring constant in N/m. The graph from slide 2 has force F on the vertical axis and extension x on the horizontal axis.

y = m x + bgeneral straight liney: vertical axis. x: horizontal axis. m: slope. b: y-intercept.F = k xHooke’s law for a springF is on the vertical axis, x on the horizontal axis; k multiplies x.

Line up the two equations

A straight line follows y = mx + b.

  • m is the slope.
  • b is the intercept, on the vertical axis.

Hooke’s law is F = kx. F is force. k is the spring constant in N/m. x is the extension.

  1. F is on the vertical axis, so F plays y.
  2. x is on the horizontal axis: x plays x.
  3. The number multiplying x is the slope: m is k.

So 25.0 N/m is k. The 0.50 N intercept is not in Hooke’s law. The meter did not read zero.

Givens: a cart’s speed v is plotted against time t, and the line of best fit has the equation v = v₀ + at, where a is constant acceleration. Question: using y = mx + b, what does the slope represent, and what does the vertical intercept represent?

012345605101520speed v (m/s)time t (s)

Sometimes the intercept is the physics

A cart’s speed v is plotted against time t. The line is v = v₀ + at.

  • a is the constant acceleration in m/s².
  • v₀ is the starting speed in m/s.

Compare with y = mx + b. Ask:

  1. Which symbol plays y? Which plays x?
  2. Which is multiplied by x? That is the slope.
  3. Which stands alone? That is the intercept.

Then say what each one means in physics, with units.

Diploma: ask if the physics equation has a b term.

Compare after your attempt

Match v to y, t to x. The number multiplying t is a, so the slope equals the acceleration a (in m/s per s, or m/s²).

The term with no t is v₀, which plays the role of b. The vertical intercept is the initial speed v₀. Here the intercept is real physics, not an error. Always ask whether the physics equation has a b term.

Predict with the whole line, intercept included

Watch this part in the video

On a small screen, scroll sideways to read the labels.

Slide 3 matched the line to y = mx + b. Now use the line to predict.
Givens from the line in slide 2: F = (25.0 N/m)x + 0.50 N, from a spring experiment. Find the extension that this experiment predicts for a force of 1.20 N.

0246810120.01.02.03.04.0force F (N)extension x (×10⁻² m)from the linefrom F = kx alone

Use y = mx + b, not F = kx alone

Predict with the whole line: F = (25.0 N/m)x + 0.50 N. Find x for F = 1.20 N.

The textbook law, x = F ÷ k, gives 0.0480 m. But the line crosses the force axis at 0.50 N. That law leaves out the 0.50 N.

  1. Put in F: 1.20 = 25.0x + 0.50.
  2. Subtract the intercept: 0.70 = 25.0x.
  3. Divide: x = 0.70 ÷ 25.0 = 0.0280 m.

Givens: the same line, F = (25.0 N/m)x + 0.50 N. The extension is 6.0 cm. Find the predicted force.

0246810120.01.02.03.04.0force F (N)extension x (×10⁻² m)

Predicting a force from an extension

The line is F = (25.0 N/m)x + 0.50 N. The extension is 6.0 cm.

  1. Convert to metres: 6.0 cm = 0.060 m.
  2. Substitute: F = 25.0 × 0.060 + 0.50.
  3. 25.0 × 0.060 = 1.50, so F = 1.50 + 0.50 = 2.00 N.

Stay inside the measured range, or just beyond it.

Givens: the same line, F = (25.0 N/m)x + 0.50 N. A force of 2.30 N is applied. Question: find the extension this experiment predicts, in metres.

0246810120.01.02.03.04.0force F (N)extension x (×10⁻² m)

Fresh prediction: extension from a force

Use the same line: F = (25.0 N/m)x + 0.50 N. Find x for F = 2.30 N.

  1. Write the equation with 2.30 in place of F.
  2. Subtract 0.50 N from both sides.
  3. Divide by the slope, in N/m.

The extension comes out in metres. Leaving out the intercept makes it too large.

Starting point if needed

Subtract 0.50 N from the force before dividing by 25.0 N/m.

Compare after your attempt

2.30 N = (25.0 N/m)x + 0.50 N. Subtract 0.50 N: 1.80 N = (25.0 N/m)x.

x = 1.80 N ÷ 25.0 N/m = 0.072 m. Ignoring the intercept would give 0.092 m, which is too large by 0.020 m.

New situation: the same spring is stretched 9.0 cm. Question: find the force this experiment predicts. Decide whether the answer is reliable, given that the measured extensions on the graph go up to 12 × 10⁻² m.

0246810120.01.02.03.04.0force F (N)extension x (×10⁻² m)

Changed unit: predict a force from 9.0 cm

The spring is stretched 9.0 cm. Find the force. Can you trust it?

  1. Convert to metres first.
  2. Use the whole line.
  3. Compare with the measured range: up to 12 × 10⁻² m.

Inside the range is interpolation. It is reliable. Past the range is extrapolation. It is less reliable, because the line may not stay straight.

Diploma: “Is the prediction reliable?” needs a reason about the measured range.

Compare after your attempt

Convert: 9.0 cm = 0.090 m. F = (25.0 N/m)(0.090 m) + 0.50 N = 2.25 N + 0.50 N = 2.75 N.

The extension is inside the measured range (up to 0.12 m), so this prediction is an interpolation and is reasonably reliable. A prediction far past 0.12 m would be an extrapolation.

Method: how to get slope and constants from a graph

On a small screen, scroll sideways to read the labels.

These are the steps from slides 2 to 4.
Use this method whenever a question gives a straight line of best fit and asks for a slope, a constant or a prediction.

1Pick two points2Find slope3Match y = mx + b4Say what they mean5Predict

Method: how to get slope and constants from a graph

  1. Pick two points on the line. Choose points where grid lines cross and far apart. Use line points, never data points.
  2. Find the slope. Slope = rise ÷ run. Keep the power of ten in the run, and give the unit: vertical unit ÷ horizontal unit.
  3. Match y = mx + b. Ask which symbol plays y, which plays x, what multiplies x, and what stands alone.
  4. Say what they mean. Say what the slope and the intercept are in physics, with units. Does the physics equation have a b term?
  5. Predict with the whole line. Put the value into y = mx + b and keep the intercept.

Check: The slope unit is the vertical unit ÷ the horizontal unit, and the answer has a size that fits the picture.

Used again in: slide 6 (the field graph), slide 7 (the straightened curve), and the graph questions in B6 to B8 and B14.

Givens (the spring graph of this lesson): A and B lie on the line F = 25.0x + 0.50. Find the spring constant, then the extension for 1.20 N.

1Pick two points2Find slope3Match y = mx + b4Say what they mean5Predict

Run-through: the spring line

The spring graph of this lesson, step by step: find the spring constant, then the extension for a force of 1.20 N.

  1. Step 1A (2.0 × 10⁻² m, 1.00 N) and B (10.0 × 10⁻² m, 3.00 N), both on the line at grid crossings.
  2. Step 2Rise = 3.00 − 1.00 = 2.00 N. Run = (10.0 − 2.0) × 10⁻² m = 0.080 m. Slope = 2.00 ÷ 0.080 = 25.0 N/m.
  3. Step 3Compare F = 25.0x + b with y = mx + b. F plays y, x plays x, and 25.0 N/m multiplies x.
  4. Step 4The slope is the spring constant, k = 25.0 N/m. The intercept, 0.50 N, is an offset. Hooke’s law has no b.
  5. Step 5Use the whole line: 1.20 = 25.0x + 0.50, so 0.70 = 25.0x and x = 0.0280 m.

Find Coulomb’s constant from a field graph

Watch this part in the video

On a small screen, scroll sideways to read the labels.

Now use the same steps on the field from B4.
Givens: in this part k is Coulomb’s constant, not a spring constant. A probe measures field strength E (N/C) at a fixed distance r = 0.500 m from a source of charge Q (C). The source charge Q is changed from 2 to 12 μC, and E is plotted against Q. The line of best fit does not pass through the origin.

r = 0.500 m, kept fixed+source Qprobe reads EE = (k / r²) Qy = m xslope = k / r²

Set up the experiment and the comparison

Use a line to find a constant of nature. Here k is Coulomb’s constant, not a spring constant.

E = kQ/r². E is field strength in N/C. Q is source charge in C. r is distance in m.

A probe measures E at r = 0.500 m. Q goes from 2 to 12 μC. E is plotted against Q.

  • Q is manipulated, so it goes across.
  • E is responding, so it goes up.
  • r and k stay fixed.

The slope is k/r², so k = slope × r².

Givens: J = (2.0 μC, 1.0 × 10⁵ N/C) and K = (10.0 μC, 4.0 × 10⁵ N/C) lie on the line; r = 0.500 m. The accepted value on the data sheet is 8.99 × 10⁹ N·m²/C². Find k from the graph.

024681012012345field strength E (×10⁵ N/C)source charge Q (μC)J (2.0, 1.0)K (10.0, 4.0)run = 8.0 μCrise = 3.0 × 10⁵ N/C

Read the slope, then solve for k

J is (2.0 μC, 1.0 × 10⁵ N/C). K is (10.0 μC, 4.0 × 10⁵ N/C).

  1. Rise = (4.0 − 1.0) × 10⁵ = 3.0 × 10⁵ N/C.
  2. 1 μC = 10⁻⁶ C. Run = (10.0 − 2.0) × 10⁻⁶ = 8.0 × 10⁻⁶ C.
  3. Slope = 3.0 × 10⁵ ÷ (8.0 × 10⁻⁶) = 3.75 × 10¹⁰ N/C².
  4. k = slope × r² = (3.75 × 10¹⁰)(0.500)² = 9.38 × 10⁹ N·m²/C².

Unit check: (N/C²)(m²) = N·m²/C². Data sheet: 8.99 × 10⁹. Difference: 0.39 ÷ 8.99, about 4 %.

Givens: the same line, E = (3.75 × 10¹⁰ N/C²)Q + 2.5 × 10⁴ N/C, at r = 0.500 m. A new source has Q = 7.0 μC. Question: use the experiment to predict E, in N/C.

024681012012345field strength E (×10⁵ N/C)source charge Q (μC)

Predict E for a new charge

At r = 0.500 m, use this line.

  • E = (3.75 × 10¹⁰ N/C²)Q + 2.5 × 10⁴ N/C

A new source has Q = 7.0 μC.

  1. Convert the charge to coulombs.
  2. Multiply the slope by Q.
  3. Add the intercept.

Diploma: use the full line, intercept included.

Starting point if needed

Use E = mQ + b with Q in coulombs.

Compare after your attempt

E = (3.75 × 10¹⁰ N/C²)(7.0 × 10⁻⁶ C) + 2.5 × 10⁴ N/C = 2.625 × 10⁵ N/C + 0.25 × 10⁵ N/C = 2.875 × 10⁵ N/C ≈ 2.9 × 10⁵ N/C.

Leaving out the intercept would give 2.6 × 10⁵ N/C, about 9 % too low. The graph confirms 2.9 × 10⁵ N/C at 7.0 μC.

Givens: at r = 0.300 m a line of best fit for E against Q passes through M = (3.0 × 10⁻⁶ C, 3.2 × 10⁵ N/C) and N = (9.0 × 10⁻⁶ C, 9.5 × 10⁵ N/C). Question: find the experimental value of Coulomb’s constant. Record your answer as a.bc × 10ⁿ N·m²/C².

0246810024681012field strength E (×10⁵ N/C)source charge Q (μC)MN

Diploma-style numerical response

At r = 0.300 m, E is plotted against Q. The line of best fit passes through M and N. Find Coulomb’s constant.

  1. Slope = rise ÷ run. Keep the power of ten in the run, using the charges.
  2. The slope equals k ÷ r². So multiply by r², not divide.
  3. Write a.bc × 10ⁿ, with units.

Check the size against the data-sheet k.

Compare after your attempt

Rise = (9.5 − 3.2) × 10⁵ N/C = 6.3 × 10⁵ N/C. Run = (9.0 − 3.0) × 10⁻⁶ C = 6.0 × 10⁻⁶ C. Slope = 1.05 × 10¹¹ N/C².

k = slope × r² = (1.05 × 10¹¹ N/C²)(0.300 m)² = 9.45 × 10⁹ N·m²/C². Record 9.45 × 10⁹.

Straighten a curve: plot against 1/r²

Watch this part in the video

On a small screen, scroll sideways to read the labels.

On slide 6 the graph was a straight line. Coulomb’s law from B2 gives a curve.
Givens: two fixed point charges, Q₁ = 3.00 μC and Q₂ = 2.00 μC. The separation r is changed and the force F is measured at four separations. F is plotted against r.

0.00.20.40.60.81.01.20.00.10.20.30.40.50.6force F (N)separation r (m)

A curve cannot give a slope

Many graphs are curves. Take fixed charges Q₁ = 3.00 μC and Q₂ = 2.00 μC. Use sizes only, with no minus signs.

F against r is a curve. A curve has no single slope.

Coulomb’s law: F = kQ₁Q₂ × (1/r²). F is proportional to 1/r², not to r.

So plot F against 1/r². Then F = (kQ₁Q₂) × (1/r²) matches y = mx: a straight line.

Givens: Q₁ = 3.00 μC, Q₂ = 2.00 μC. The separations were 1.00, 0.707, 0.500 and 0.316 m. Points C and D on the line of best fit are (2.0 m⁻², 0.108 N) and (10.0 m⁻², 0.524 N). Find k.

0246810120.00.20.40.6force F (N)1/r² (m⁻²)C (2.0, 0.108)D (10.0, 0.524)

Make the new axis, read the slope, find k

The horizontal values are 1/r²: 1.00, 2.00, 4.00 and 10.0 m⁻². Example: 0.500² = 0.250, and 1 ÷ 0.250 = 4.00.

  1. Two points: C (2.0 m⁻², 0.108 N) and D (10.0 m⁻², 0.524 N).
  2. Slope = (0.524 − 0.108) ÷ (10.0 − 2.0) = 0.0520 N·m². The unit is N ÷ m⁻² = N·m².
  3. Slope = kQ₁Q₂. Q₁Q₂ = (3.00 × 10⁻⁶)(2.00 × 10⁻⁶) = 6.00 × 10⁻¹² C².
  4. k = 0.0520 ÷ (6.00 × 10⁻¹²) = 8.67 × 10⁹ N·m²/C².

Givens: two equal charges, Q₁ = Q₂ = 4.00 μC. A line of F against 1/r² passes through G = (2.0 m⁻², 0.31 N) and H = (8.0 m⁻², 1.20 N). Question: find the experimental value of Coulomb’s constant.

02468100.00.40.81.21.6force F (N)1/r² (m⁻²)GH

Fresh data, same method

Now the two charges are equal: Q₁ = Q₂ = 4.00 μC. A line of F against 1/r² passes through G and H. Find Coulomb’s constant.

  1. The slope is kQ₁Q₂. Write the charge product.
  2. Find the slope from G and H. Keep the units.
  3. Divide the slope by the charge product. That leaves k.
Starting point if needed

The slope equals kQ₁Q₂. Both charges are 4.00 × 10⁻⁶ C.

Compare after your attempt

Slope = (1.20 − 0.31) N ÷ (8.0 − 2.0) m⁻² = 0.890 ÷ 6.0 = 0.1483 N·m². The charge product is (4.00 × 10⁻⁶ C)² = 1.60 × 10⁻¹¹ C².

k = slope ÷ (Q₁Q₂) = 0.1483 ÷ (1.60 × 10⁻¹¹) = 9.27 × 10⁹ N·m²/C².

New situation: for a point source with fixed charge Q, the field E = kQ/r² is measured at several distances r. Question: what should be plotted on each axis to give a straight line, and what does the slope equal?

Point source, Q fixed, r changes.E = kQ / r²x-axis: ?slope: ?

Changed law: straighten E against r

A point source has a fixed charge Q. The field E = kQ/r² is measured at several distances r.

Compare E = kQ/r² with y = mx. Ask:

  1. What is y? What is x?
  2. What multiplies x?

Q is fixed, so it belongs in the slope. Say what the slope equals, then how to pull k out of it.

Diploma: “what should be plotted” has a clear answer.

Compare after your attempt

Plot E on the vertical axis and 1/r² on the horizontal axis. E = (kQ)(1/r²) matches y = mx.

The slope equals kQ. To isolate k, divide the slope by the fixed source charge Q.

Method: how to straighten a curve

On a small screen, scroll sideways to read the labels.

These are the steps you used on slide 7.
Use this method whenever a graph is a curve and the question asks for a constant of nature.

1Name the relation2Choose what toplot3Make new column4Plot and fit aline5Read slope, find k

Method: how to straighten a curve

  1. Name the relationship. Say what the law says: the force is proportional to 1/r², not to r.
  2. Choose what to plot. Plot against the quantity the law is proportional to. Here that is 1/r².
  3. Make the new column. Square each r, then flip it. Keep an extra digit until the column is finished.
  4. Plot and draw the line. Plot the new column on the horizontal axis. Draw one line of best fit through the points.
  5. Read the slope and find the constant. Use two points on the line. The slope holds every constant, so divide by the ones you know.

Check: The points fall on a straight line near the origin, and the slope unit is the vertical unit ÷ m⁻².

Used again in: B12 and the graph questions in B14.

Givens (the curve of this lesson): Q₁ = 3.00 μC, Q₂ = 2.00 μC, and r = 1.00, 0.707, 0.500 and 0.316 m. Find k.

1Name the relation2Choose what toplot3Make new column4Plot and fit aline5Read slope, find k

Run-through: force against 1/r²

The curve of this lesson, step by step: Q₁ = 3.00 μC and Q₂ = 2.00 μC, with separations of 1.00, 0.707, 0.500 and 0.316 m.

  1. Step 1F = kQ₁Q₂ × (1/r²), so F is proportional to 1/r².
  2. Step 2Plot F against 1/r².
  3. Step 30.500² = 0.250 and 1 ÷ 0.250 = 4.00. The column is 1.00, 2.00, 4.00 and 10.0 m⁻².
  4. Step 4The points fall on a line. Two points on it are C (2.0 m⁻², 0.108 N) and D (10.0 m⁻², 0.524 N).
  5. Step 5Slope = (0.524 − 0.108) ÷ (10.0 − 2.0) = 0.0520 N·m². The charge product is Q₁Q₂ = (3.00 × 10⁻⁶)(2.00 × 10⁻⁶) = 6.00 × 10⁻¹² C². Then k = 0.0520 ÷ (6.00 × 10⁻¹²) = 8.67 × 10⁹ N·m²/C².

Practice question

A line of best fit for a spring passes through (1.0 × 10⁻² m, 0.55 N) and (7.0 × 10⁻² m, 2.65 N). Find the slope with its unit.

Hint

Slope = rise ÷ run. Keep the × 10⁻² in the run.

Compare after your attempt

Rise = 2.65 N − 0.55 N = 2.10 N. Run = (7.0 − 1.0) × 10⁻² m = 0.060 m. Slope = 2.10 ÷ 0.060 = 35.0 N/m.

Practice question

The line in the previous question has the equation F = (35.0 N/m)x + 0.20 N. What extension does the experiment predict for a force of 1.60 N?

Hint

Put 1.60 N in place of F. Subtract the intercept before you divide by the slope.

Compare after your attempt

1.60 N = (35.0 N/m)x + 0.20 N. Subtract 0.20 N: 1.40 N = (35.0 N/m)x. x = 1.40 ÷ 35.0 = 0.0400 m, or 4.00 cm.

Practice question

Students measure the force between two fixed charges at several separations and want a straight-line graph. What should they plot on each axis, and what does the slope equal?

Hint

Plot against the quantity that the force is proportional to.

Compare after your attempt

Plot F on the vertical axis and 1/r² on the horizontal axis. Since F = kQ₁Q₂(1/r²), the slope equals kQ₁Q₂.

Practice question

The field-strength experiment is repeated with the probe 0.800 m from the source. The new line of best fit has slope 1.46 × 10¹⁰ N/C². Find the experimental value of k, with its unit.

Hint

The slope equals k/r². What must you do to the slope to leave k?

Compare after your attempt

The slope equals k/r², so k = slope × r² = (1.46 × 10¹⁰ N/C²)(0.800 m)² = 9.34 × 10⁹ N·m²/C².

Practice question

The same spring is stretched 9.0 cm. Its line of best fit is F = (25.0 N/m)x + 0.50 N, with measured extensions up to 12 cm. Find the force this experiment predicts, and say whether the prediction is reliable.

Hint

Change cm to m and use the whole line. Then compare 9.0 cm with the measured range.

Compare after your attempt

9.0 cm = 0.090 m. F = (25.0 N/m)(0.090 m) + 0.50 N = 2.75 N. The extension is inside the measured range, so the prediction is reliable.

Practice question

In an experiment, only the source charge Q is changed and the distance r is held fixed. E is plotted against Q. Write E = kQ/r² in the form y = mx, say what the slope equals, and say how to find k from the slope.

Hint

Group everything that multiplies Q. That group is the slope.

Compare after your attempt

E = (k/r²)Q, so the slope equals k/r². Then k = slope × r², multiplying by r squared, not by r.

Challenge question

Challenge: A source has a fixed charge Q = 5.00 μC. The field E is measured at several distances and plotted against 1/r². The line of best fit passes through (4.0 m⁻², 1.75 × 10⁵ N/C) and (16.0 m⁻², 7.25 × 10⁵ N/C). Find the experimental value of k, and its percent difference from the data-sheet value 8.99 × 10⁹ N·m²/C².

Hint

Match E = (kQ)(1/r²) to y = mx. The slope is kQ, so divide the slope by Q.

Compare after your attempt

Slope = (7.25 × 10⁵ − 1.75 × 10⁵) ÷ (16.0 − 4.0) = 4.583 × 10⁴ N·m²/C. Since E = (kQ)(1/r²), the slope equals kQ. So k = slope ÷ Q = (4.583 × 10⁴) ÷ (5.00 × 10⁻⁶) = 9.17 × 10⁹ N·m²/C². Percent difference = (9.17 − 8.99) ÷ 8.99 × 100 = 2.0 %.