All lessons

The generator effect and Lenz’s law

Complete reading and printing route. Attempt each question before reading its feedback. All diagram stages are included below.

After the lesson: Investigate and connect: a short investigation, a data step and a real-world link.

A moving rod separates charge

Watch this part in the video

On a small screen, scroll sideways to read the labels.

In B14, a current in a field gave a force and motion. This lesson runs that backward.
Givens: a metal rod is pulled to the right through a magnetic field that points into the page. The rod contains many free electrons, and they move along with it.

v+−

Motion in, potential difference out

The generator effect is motion in, electricity out.

Pull a rod through a field. Its electrons move through the field too. Each feels a force.

  1. Fingers along the field B.
  2. Thumb along the rod’s velocity v.
  3. Palm shows the force on a positive charge.
  4. Reverse it for electrons.

Here the fingers point into the page and the thumb points right. The palm faces up. So electrons go down, and the bottom end is negative.

Givens: a horizontal metal rod is pulled straight down the page through a magnetic field that points into the page. Question: which end of the rod, left or right, becomes positive?

v

Which end is positive?

A rod moves through a field. Find which end gathers the electrons.

  1. Use the right hand to find the force on a positive charge.
  2. Reverse it, because the free charges are electrons.
  3. The end where electrons gather is negative.

Say left or right, and give one reason.

Diploma: the end where electrons gather is negative.

Starting point if needed

Find the force on a positive charge with the right hand, then reverse it for the electrons.

Compare after your attempt

For a positive charge the thumb points down and the fingers point into the page, so the force is to the right.

The electrons are negative, so they are pushed to the left and gather at the left end. The right end is positive.

New situation: a vertical rod is pulled to the right through a magnetic field that points out of the page. Question: which end of the rod, top or bottom, becomes positive, and how does this compare with the field into the page?

v

Changed field: out of the page

The rod is vertical and moves right. Find the force on the electrons first. Then name the ends.

  1. Use the right hand. Then reverse it.
  2. Which end, top or bottom, gathers electrons?
  3. Which end is positive?

Only the field direction changes. What happens to the ends?

Compare after your attempt

With the fingers pointing out of the page and the thumb pointing right, the palm faces down, so a positive charge would be pushed down. The electrons are pushed up.

The top end is negative and the bottom end is positive, the opposite of the field-into-the-page case.

How large is the potential difference?

On a small screen, scroll sideways to read the labels.

On slide 1, a moving rod got a positive end and a negative end. Now find the voltage between them.
Givens: a rod of length l moves at speed v at right angles to a field B and to its own length. The size of the potential difference ΔV between its ends is ΔV = Blv; B is in tesla, l in metres and v in metres per second. The equation is not on the data sheet, so you will be given it when it is needed.

l = 0.40 m v = 3.0 m/s B = 0.250 T

Speed, length and field

Three things set the size of the potential difference.

  • A faster rod gives a bigger force on each electron.
  • A longer rod lets the force act over more distance.
  • A stronger field gives a bigger force.

Formula: ΔV = Blv. ΔV is the potential difference between the ends.

  • B = field (T)
  • l = rod length (m). B14 wrote length as L.
  • v = speed (m/s)

ΔV = (0.250 T)(0.40 m)(3.0 m/s) = 0.300 V.

Givens: a rod of length 0.60 m moves at right angles to a magnetic field of 0.150 T and to its own length. The potential difference between its ends is 0.90 V. Question: what is the speed of the rod?

l = 0.60 m B = 0.150 T ΔV = 0.90 V v = ?

Speed needed for a given voltage

Here ΔV is given and v is unknown. The rod moves at right angles to the field and to its length.

  1. Write ΔV = Blv.
  2. Divide both sides by Bl.
  3. Put in ΔV, B and l with units.

The answer is in m/s.

Diploma: write the rearranged form before the numbers.

Starting point if needed

Rearrange ΔV = Blv to get v alone, and divide by both B and l.

Compare after your attempt

ΔV = Blv, so v = ΔV/(Bl).

v = 0.90 V/[(0.150 T)(0.60 m)] = 10.0 m/s.

Givens: a rod moves through a field and produces a potential difference ΔV. A second rod has twice the length, moves at half the speed, and is in a field three times as strong. Question: what is the potential difference of the second rod? A. ΔV/3. B. ΔV. C. 3ΔV. D. 6ΔV. Choose one letter.

l, v, B2 l, ½ v, 3 B

Compare two rods

Compare two rods. Three factors set ΔV, and each one changes.

  1. Write ΔV = Blv for the first rod.
  2. Write what each factor becomes for the second rod.
  3. Multiply the three changes. Do not add them.
Compare after your attempt

ΔV is proportional to the product Blv. The factors are 2 for the length, ½ for the speed and 3 for the field.

2 × ½ × 3 = 3, so the new potential difference is 3ΔV. Answer C.

Closing the circuit

Watch this part in the video

On a small screen, scroll sideways to read the labels.

On slides 1 and 2 the rod was alone, so no current could flow. Now give the charge a path.
Givens: the rod slides on two rails, which are parallel metal bars. A resistor, a part that uses up electrical energy, joins the right-hand ends of the rails, and the rod is at the left, so the circuit is closed. The rod is pulled to the right through a field that points into the page.

Rv

A current in the circuit

The rod slides on two rails, which are parallel metal bars. A resistor (a part that uses electrical energy, like a lamp) joins the rail ends. The circuit is closed.

  1. The rod acts like a battery. The top end is positive.
  2. Conventional current leaves the positive end.
  3. It goes along the top rail, down through the resistor, back along the bottom rail.
  4. Inside the rod it goes from negative to positive.

Seen from the front, the current goes clockwise.

Givens: the same circuit and field (into the page), but now the rod is pulled to the left. Question: does conventional current go clockwise or counterclockwise around the circuit?

Rv

Pull it the other way

The rod now moves left. Which end is positive?

  1. Reverse the velocity. The force on the electrons reverses.
  2. So the positive end reverses.
  3. Trace the current.

Check: it must be opposite to the rod moving right.

Starting point if needed

Reversing the velocity reverses the force on the electrons, so it reverses the current.

Compare after your attempt

With the rod moving left, the force on the electrons is up, so they gather at the top: the bottom end is positive.

Conventional current leaves the bottom end and goes the opposite way round the circuit: counterclockwise.

New situation: the same rails and rod, with the field now out of the page, and the rod is pulled to the right. Question: does conventional current go clockwise or counterclockwise, and which end of the rod is positive?

Rv

Changed field: out of the page

The rod moves right. The field is out of the page.

  1. Right hand: thumb along v, fingers along B. This is the force on a positive charge.
  2. Electrons go the other way. Find the positive end.
  3. Conventional current leaves it. Say clockwise or counterclockwise.

Diploma: find the ends first, then the current.

Compare after your attempt

With the field out of the page and the rod moving right, the palm of the right hand faces down, so the electrons are pushed up. The bottom end is positive.

Conventional current leaves the bottom end and flows counterclockwise around the circuit.

A magnet and a coil

Watch this part in the video

On a small screen, scroll sideways to read the labels.

On slide 3, a moving rod drove a current. A moving magnet near a coil does the same.
Givens: a coil is joined to a sensitive current meter, and a bar magnet is moved near it. A magnet that is held still gives no current. A magnet that is moving gives one.

SN

Only a changing situation gives a current

Move the magnet or the coil, so one moves past the other. The electrons in the coil feel a force. This is electromagnetic induction. Michael Faraday discovered it in 1831.

  • Current flows only while they move.
  • Push the south pole in, and current flows one way. Pull it out, and it flows the other way.
  • Pushing the north pole in gives the opposite current.
  • A faster motion, a stronger magnet or more turns gives more current.

Givens: pushing the south pole of a bar magnet into a coil at a steady speed deflects the meter needle to the right. Question: predict the needle for (a) pulling the same pole out at the same speed, (b) pushing the north pole in at the same speed, (c) pushing the south pole in twice as fast, and (d) holding the magnet still inside the coil.

SN

Predict the meter

Use the list to predict the meter. For each change, ask what changed.

  • The direction of motion, or the pole.
  • The speed.
  • No motion at all.

Reverse the motion or the pole, and the needle reverses. Go faster, and only the size changes. With no motion there is no current.

Diploma: “predict” answers need a reason. Say what you changed.

Starting point if needed

Reverse the motion or reverse the pole and the direction reverses; faster motion changes only the size.

Compare after your attempt

(a) Pulling it out reverses the motion, so the needle goes left. (b) Pushing the north pole in reverses the pole, so the needle goes left.

(c) Twice as fast gives the same direction (right) with a larger deflection, about twice. (d) A magnet held still gives no current, so the needle stays at zero.

Motors and generators

Watch this part in the video

On a small screen, scroll sideways to read the labels.

B14 built a motor. Slides 1 to 4 built a generator. They are the same machine.
Givens: an electric motor has a coil, magnets and a source of electrical energy. A generator has the same parts but takes in motion. A small motor and a hand-cranked generator are often the same device.

electrical energy in → motion outmotion in → electrical energy out

One machine, two directions

The same device works both ways.

  • Motor effect: electricity in, motion out.
  • Generator effect: motion in, electricity out.

A generator joined to a lamp is harder to turn. Its current is in a field, so it feels a force that resists the turning. Slide 6 shows why.

Diploma: name the energy change.

Givens: a hand-cranked generator is easy to turn when its wires are not connected to anything. It gets noticeably harder to turn when it is connected to a lamp that lights. Question: use what you know to explain why it is harder to turn when connected, and where the extra energy goes.

Easy to turn, hard to turn

Explain why a generator is easier to turn when nothing is connected.

  1. With no lamp, is there a current in the coil?
  2. No current means no magnetic force.
  3. With a lamp: say which way the force acts compared with the turning.
  4. Where does the extra work go? Into the electrical energy of the lamp.
Starting point if needed

Current in a coil in a magnetic field leads to a magnetic force.

Compare after your attempt

With the circuit open there is no current, so there is no magnetic force on the coil and it turns easily.

With the lamp connected there is a current in a magnetic field, so there is a magnetic force that resists the turning. The extra work you do against it becomes the lamp’s energy.

Lenz’s law: the force opposes the motion

Watch this part in the video

On a small screen, scroll sideways to read the labels.

On slide 5, a generator joined to a lamp was harder to turn. This slide shows why.
Givens: a strong magnet is dropped down a vertical aluminium tube 0.30 m long. Aluminium is a good conductor, but it is not magnetic, so the magnet is not pulled toward it. The same magnet dropped through air falls the 0.30 m in about 0.25 s, yet in the tube it takes two to three seconds.

NSv

A magnet that falls in slow motion

In air the magnet falls 0.30 m in about 0.25 s. In the tube it takes two to three seconds.

  1. The magnet moves, so its field sweeps through the aluminium.
  2. Small circular currents flow in the tube. This is an induced current: it has no battery.
  3. A current in a field feels a force. It acts on the magnet.
  4. The force opposes the motion. The magnet falls, so the force is up.

Lenz’s law: the force from an induced current opposes the motion that caused it.

Givens: three rods of the same size, one of plastic, one of aluminium and one of copper. A ring magnet is dropped over the top of each rod from the same height at the same time. Copper conducts electricity better than aluminium, and plastic is an insulator. Question: put the three rods in order from the one where the magnet falls fastest to the one where it falls slowest, and explain the order.

plasticaluminiumcopper

Which rod is slowest?

Plastic is an insulator. The other two rods are conductors.

  1. In which rods can a current flow?
  2. No current means no force.
  3. A better conductor has a bigger current and a bigger force.
  4. Order the rods, fastest fall to slowest.

Give one reason for each. Use “induced current” and “opposing force”.

Diploma: give the order first, then a reason for each.

Starting point if needed

No current means no force. A better conductor carries a larger current.

Compare after your attempt

Plastic is fastest. It is an insulator, so there is no induced current, no force and the magnet falls as if the rod were not there.

Aluminium is slower, because it carries induced currents that give an opposing force. Copper is slowest, because it is the better conductor, so the current and the opposing force are largest.

New situation: a pendulum with a strong magnet at its end swings between two aluminium blocks. It is moving to the right through the lowest point. Question: what is the direction of the magnetic force on the magnet right now, what happens to the swing as time passes, and does the direction of this force change when the pendulum swings back to the left?

NAlAlv

A swinging pendulum between blocks

A pendulum with a magnet swings between two aluminium blocks. It moves right through its lowest point.

  1. Lenz’s law: the force opposes the motion. Which way is that?
  2. Does the force add energy or take it away?
  3. Does the force stay the same, or follow the motion?
Compare after your attempt

The pendulum is moving to the right, so the magnetic force on the magnet is to the left, opposing the motion.

The swing dies away very quickly, because the force always opposes the motion. When the pendulum swings to the left, the force is to the right, so the direction of the force changes with the motion but it always opposes it.

Lenz’s law for a coil: which way the current goes

On a small screen, scroll sideways to read the labels.

Slide 6 gave Lenz’s law for a falling magnet. Now use it on the coil from slide 4.
Givens: a coil is joined to a meter, so the circuit is closed. The north pole of a bar magnet is pushed toward the left end of the coil. Recall from B10: a coil that carries a current is a magnet, and the field lines leave its north end.

meterNSSNv

The coil pushes back

Lenz’s law also tells you which way the induced current goes in a coil. The coil becomes a magnet that opposes the motion.

  1. Which way is the magnet moving? Here the north pole moves closer.
  2. Which pole opposes that? Moving closer needs the same pole, to repel. Moving away needs the opposite pole, to attract.
  3. Grip a front wire. The field inside the coil points to its north end.

Here the left end is north. Thumb up gives a field to the left, so the current is up.

Givens: the same coil and meter. The north pole of a bar magnet is pushed toward the right end of the coil. Question: (a) which pole does the right end of the coil become? (b) Which way does the conventional current go in the wires on the front of the coil, up or down? (c) The magnet is then pulled back out. What happens to the pole and to the current?

meterNSv

North pole toward the right end

Now the north pole moves toward the right end of the coil.

  1. The magnet moves closer. Must the coil push it away or pull it in?
  2. Which pole does the right end become?
  3. Try the grip both ways on a front wire. Which way makes that pole?

Then the magnet is pulled out. The motion reverses, so the pole and the current reverse.

Starting point if needed

A magnet moving closer must be repelled. The field inside a coil points toward its north end.

Compare after your attempt

(a) The magnet is moving closer, so the coil must repel it. The right end becomes a north pole.

(b) The field inside the coil points right, toward the north end. Thumb down on a front wire puts the fingers pointing right inside the coil, so the current in the front wires is down.

(c) The coil must now attract the magnet, so the right end becomes a south pole and the current reverses to up.

Method: how to find an induced voltage and its direction

On a small screen, scroll sideways to read the labels.

These are the steps you used on slides 1 to 3.
Use this method whenever a rod moves through a magnetic field and a question asks for the potential difference, the positive end or the direction of the current.

1List v, B and l2Find the size3Find the ends4Trace the current5Check with Lenz

Method: how to find an induced voltage and its direction

  1. List v, B and l. All at right angles. Units: m/s, T, m.
  2. Find the size. ΔV = Blv. Keep every digit.
  3. Find the ends. Right hand, then reverse for electrons. They gather at the negative end.
  4. Trace the current. It leaves the positive end. Say clockwise or counterclockwise.
  5. Check with Lenz’s law. The force on the rod’s current opposes v.

Check: Volts. Reverse v or B: every direction flips. Stop the rod: ΔV = 0.

Used again in: practice Q2, Q3 and Q6.

Givens (the rod from slides 2 and 3): a 0.40 m rod is pulled to the right at 3.0 m/s through a field of 0.250 T that points into the page, and it is part of a closed circuit with a resistor.

1List v, B and l2Find the size3Find the ends4Trace the current5Check with Lenz

Run-through: the rod pulled to the right

The rod from slides 2 and 3: v = 3.0 m/s right, B = 0.250 T into the page, l = 0.40 m, in a closed circuit.

  1. Step 1v, B and l are at right angles.
  2. Step 2ΔV = (0.250 T)(0.40 m)(3.0 m/s) = 0.300 V.
  3. Step 3Fingers in, thumb right: palm up. Electrons go down. Bottom is negative, top is positive.
  4. Step 4Current leaves the top end: top rail, resistor, bottom rail. Clockwise.
  5. Step 5In the rod the current goes up. The force is left, opposite to v. Lenz’s law agrees.

Practice question

What is the difference between the motor effect and the generator effect?

Hint

For each effect, say what goes in and what comes out.

Compare after your attempt

In the motor effect, electrical energy goes in and a force and motion come out. In the generator effect, motion goes in and a potential difference and current come out.

Practice question

A vertical rod is pulled to the right through a magnetic field that points into the page. Which end of the rod, top or bottom, becomes positive?

Hint

Use the right hand for a positive charge. Then reverse it for the electrons.

Compare after your attempt

The right hand gives an upward force on a positive charge, so the force on the electrons is down. They collect at the bottom, which becomes negative, so the top becomes positive.

Practice question

A 0.80 m rod moves at 5.0 m/s at right angles to a field of 0.040 T and to its own length. What is the potential difference between its ends?

Hint

Use ΔV = Blv. Everything is at right angles.

Compare after your attempt

ΔV = Blv = (0.040)(0.80)(5.0) = 0.16 V.

Practice question

A magnet is pushed into a coil and the meter shows a current. List three changes that would make the current larger.

Hint

What makes each electron feel a bigger force? What lets more loops feel it?

Compare after your attempt

Move the magnet faster, use a stronger magnet, or use a coil with more turns.

Practice question

Why is a generator harder to turn when it is connected to a lamp?

Hint

Is there a current in the coil? What does a current in a field feel?

Compare after your attempt

A current flows in the coil, which is in a magnetic field, so the coil feels a magnetic force that resists the turning. Extra work is done against this force and becomes the electrical energy in the lamp.

Practice question

A magnet is dropped down a vertical aluminium tube. In which direction is the magnetic force on the magnet, and why does it fall slowly?

Hint

Lenz’s law: the force opposes the motion.

Compare after your attempt

The force on the magnet is up, opposite to its downward motion. The moving magnet induces currents in the aluminium, and the magnetic force from those currents opposes the motion, so the magnet drifts down slowly.

Challenge question

Challenge: A rod 0.40 m long moves through a magnetic field of 0.250 T, at right angles to the field and to its own length. What speed gives a potential difference of 1.5 V between its ends? Then say what the potential difference is if the rod moves along the field lines at the same speed, and why.

Hint

Rearrange ΔV = Blv for v. For the second part, ask whether any of the velocity is across the field.

Compare after your attempt

ΔV = Blv, so v = ΔV ÷ (Bl) = 1.5 ÷ [(0.250)(0.40)] = 15 m/s. If the rod moves along the field lines, no part of the velocity is across the field. The electrons feel no magnetic force, so no charge separates and the potential difference is zero.