All lessons

The motor effect on a current-carrying wire

Complete reading and printing route. Attempt each question before reading its feedback. All diagram stages are included below.

After the lesson: Investigate and connect: a short investigation, a data step and a real-world link.

Why a wire in a field is pushed

Watch this part in the video

On a small screen, scroll sideways to read the labels.

B11 found the force on one moving charge. A current is many moving charges in a wire.
Symbols in this lesson:
F = force (N) · I = current, in A (amperes) · L = length of wire in the field (m) · L⊥ = the part of L across the field
B = magnetic field strength, in T (tesla) · q = charge (C) · t = time (s) · θ = angle between the wire and the field
m = mass (kg) · g = 9.81 N/kg (from the data sheet)
Givens: a wire carries a current through a magnetic field. The current is moving charge. Conventional current in the wire shown flows left to right and the field points into the page.

I

Many charges, one push

A wire holds many moving charges. Each feels the same sideways push, so the whole wire is pushed. This is the motor effect: current in, force out.

  1. Use conventional current: the way positive charge would move.
  2. Fingers along the field. Thumb along the current.
  3. Palm shows the force.

Here the field is into the page and the current is to the right. The palm faces up, so the force is up the page.

Givens: a wire carries conventional current from left to right through a magnetic field that points out of the page. Question: in which direction is the magnetic force on the wire?

I

Reverse the field

The field now points out of the page. The current is still left to right. Predict first: what should change?

  1. Fingers along the field.
  2. Thumb along conventional current.
  3. Read the palm. That is the force.

If you reverse the field and keep the current, the force reverses too. Write up, down, into or out of the page.

Starting point if needed

Fingers along the field, thumb along conventional current, palm shows the force.

Compare after your attempt

The fingers point out of the page and the thumb points right, so the palm faces down the page.

The force on the wire is down the page, opposite to the case with the field into the page.

New situation: a vertical wire in the plane of the page carries electrons moving down the page. The magnetic field points to the right across the page. Question: which way is the force on the wire: into the page, out of the page, left or right?

Belectron flow

Changed context: electrons and a vertical wire

The wire is vertical and carries electrons. Every hand rule in this course uses conventional current. It points opposite to the electrons.

  1. Convert: electrons down means conventional current up.
  2. Fingers along the field. Thumb along conventional current.
  3. Read the palm: into the page, out, left or right.

Check: point your thumb along the electrons and read the back of your hand. You get the same answer.

Diploma: the word “electrons” is a trap. Convert first.

Compare after your attempt

Electrons move down, so conventional current is up the page.

Fingers point right and the thumb points up, so the palm faces into the page: the force on the wire is into the page.

The size of the force: F = I L B

Watch this part in the video

On a small screen, scroll sideways to read the labels.

Slide 1 gave the direction of the force on a wire. Now find its size.
Givens: a wire carries a current I through a length L that lies inside a magnetic field of strength B, at right angles to the field. Current is charge per time, I = q/t, measured in amperes (1 A = 1 C/s).

IL in the field

Current, length and field

Three things set the force on a wire. More current, more length in the field, or a stronger field means more force.

  • F = I L⊥ B
  • I = current (A)
  • L⊥ = length across the field (m)
  • B = field strength (T)

Only the wire inside the field counts. Units: 1 T = 1 N/(A·m).

Diploma: keep every digit. Round once, to 3 digits.

Givens: 18 C of charge pass a point in a wire in 4.0 s. A 0.120 m length of the wire lies at right angles to a uniform magnetic field of 0.450 T. Question: what is the current, and what is the size of the magnetic force on the wire?

B = 0.450 T18 C in 4.0 sL = 0.120 m in the field

From charge to force

The question gives a charge and a time, not a current. Find the current first.

  1. Write what is given and what is wanted.
  2. Current: I = q ÷ t. One ampere is one coulomb per second.
  3. Force: F = I L B. The wire is at right angles, so all of L counts.
  4. Check the unit is newtons.
Starting point if needed

Current is charge divided by time. Then use F = ILB.

Compare after your attempt

I = q/t = 18 C/4.0 s = 4.5 A.

F = ILB = (4.5 A)(0.120 m)(0.450 T) = 0.243 N.

New situation: a straight wire of length 0.20 m carries 6.0 A through a magnetic field of 0.500 T, at 30° to the field direction. Question: what is the size of the magnetic force on the wire?

30°I = 6.0 AB = 0.500 T, wire length 0.20 m

Changed context: a slanted wire

The wire makes an angle θ = 30° with the field. Only the part across the field counts, as in B11.

  1. Draw the wire and the field.
  2. Across part: L⊥ = L sin θ. It is opposite the angle.
  3. Use F = I L⊥ B.
  4. Check: the force is smaller than at 90°.
Compare after your attempt

The part of the length across the field is L sin 30° = 0.10 m.

F = I(L sin θ)B = (6.0 A)(0.10 m)(0.500 T) = 0.300 N.

Magnetic force against gravity

Watch this part in the video

On a small screen, scroll sideways to read the labels.

In B11, a magnetic force balanced gravity on a particle. A wire has weight too.
Givens: a horizontal wire of mass 1.40 g has 0.0900 m of its length in a horizontal magnetic field of 0.0500 T. The north pole is on the left, the south pole is on the right and the current is 4.00 A toward you.

NSI = 4.00 A, L = 0.0900 mB = 0.0500 T, m = 1.40 g

Net force on a wire

The field points right, from the north pole to the south pole. Point your fingers right and your thumb toward you. The palm faces up.

  • Magnetic force, up: I L B = (4.00)(0.0900)(0.0500) = 0.01800 N.
  • Gravity, down: mg = (1.40 × 10⁻³)(9.81) = 0.01373 N.
  • The forces are opposite, so subtract: 4.27 × 10⁻³ N, up.

g = 9.81 N/kg, the same as 9.81 m/s². At rest, the two forces are equal: I = mg ÷ (L B).

New situation: the wire hangs still between the magnets with the current toward you. The mass is 1.40 g, the length in the field 0.0900 m and the field 0.0500 T. Question: what current is needed to suspend the wire?

NSL = 0.0900 m, B = 0.0500 Tm = 1.40 g, I = ?

Changed unknown: the current that makes the wire float

The wire hangs still, so the two forces are equal in size. Find the current.

  1. At rest: the net force is zero.
  2. Set equal: I L B = mg.
  3. Rearrange: I = mg ÷ (L B). Then put in the numbers.
  4. Check the unit is amperes.

Use kilograms and g = 9.81 N/kg. A weaker field needs a larger current.

Diploma: “suspended” and “hangs motionless” both mean net force zero.

Compare after your attempt

A wire at rest has Fnet = 0, so ILB = mg.

I = mg/(LB) = (1.40 × 10⁻³ kg)(9.81 N/kg)/[(0.0900 m)(0.0500 T)] = 3.05 A.

Givens: a wire carries a current in a horizontal magnetic field and hangs motionless in the field. Question: which statement is correct? A. There is no force on the wire, because it is not moving. B. The magnetic force on the wire equals the force of gravity in size and is opposite in direction. C. The magnetic force on the wire is zero and gravity is balanced by the supports. D. The magnetic force and gravity are equal as vectors. Choose one letter.

NSwire stays at rest

Diploma-style multiple choice

Which options are true for a wire that hangs motionless? Start with what “motionless” tells you.

  1. No acceleration: the net force is zero.
  2. List the forces: gravity and the magnetic force.
  3. Compare: equal in size is not the same as equal as vectors. Vectors also have direction.
  4. Check each option.

A wire that is not moving still has forces on it.

Compare after your attempt

Answer B. A motionless wire has zero net force, so the magnetic force and the force of gravity are equal in size and opposite in direction.

A is wrong because stationary does not mean no force. C is wrong because the magnetic force is what balances gravity. D is wrong because the forces are in opposite directions, so they are not equal as vectors.

Method: how to choose the tool for a wire in a field

On a small screen, scroll sideways to read the labels.

These are the steps you used on slides 1 to 3.
Use this method whenever a question puts a wire that carries a current in a magnetic field and asks for a force, a current or a balance with gravity.

1Read the question2Pick the formula3Use the acrosspart4Find the direction5Add other forces

Method: how to choose the tool for a wire in a field

  1. Read the question. Write what is asked and every given. Note if the wire is at rest.
  2. Pick the formula. A current in a wire: F = ILB. One moving charge: F = qvB, from lesson B11.
  3. Use the part across the field. Use only the length in the field, and L sin θ if the wire is slanted. Change grams to kilograms.
  4. Find the direction. Right hand: fingers along the field, thumb along conventional current, palm shows the force. Electron flow? Reverse it first.
  5. Add the other forces. Gravity pulls down with mg. A wire at rest has Fnet = 0, so ILB = mg. Otherwise subtract the smaller force from the larger.

Check: Units: A·m·T gives N. Do the two forces point opposite ways? Is a wire at rest balanced?

Used again in: B14 practice questions, and B15, where the force on a moving rod uses the same hand rule.

Givens (slide 3): a horizontal wire of mass 1.40 g hangs still between a north pole on the left and a south pole on the right. 0.0900 m of its length is in the field, the field is 0.0500 T and the current is toward you. Question: what current holds the wire still, and which way is the magnetic force?

1Read the question2Pick the formula3Use the acrosspart4Find the direction5Add other forces

Run-through: the wire that floats

The floating wire from slide 3, step by step: the wire has mass 1.40 g, 0.0900 m is in a field of 0.0500 T, and the current is toward you.

  1. Step 1Asked: the current that holds the wire still. Given: m = 1.40 g, L = 0.0900 m, B = 0.0500 T. The wire is at rest.
  2. Step 2A current in a wire, so use F = ILB, not qvB.
  3. Step 3The wire is at right angles to the field, so L = 0.0900 m. Change the mass: 1.40 g = 1.40 × 10⁻³ kg.
  4. Step 4The field points right, from north to south. Fingers right, thumb toward you, palm up: the magnetic force is up and gravity is down.
  5. Step 5At rest, so Fnet = 0 and ILB = mg. Keep the full value: mg = (1.40 × 10⁻³)(9.81) = 1.3734 × 10⁻² N. I = 1.3734 × 10⁻² ÷ [(0.0900)(0.0500)] = 3.052 A, so I = 3.05 A.

Reading a force graph

Watch this part in the video

On a small screen, scroll sideways to read the labels.

In B5, the slope of a line gave a constant. Do the same for a wire on a balance.
Givens: a wire rests on supports on a balance pan and carries a current in a magnet’s field, so the magnetic force pushes down on it. The balance reads the magnetic force plus the force of gravity on the wire and its supports. The graph shows the reading F against the current I.

01234560.00.20.40.60.81.0scale reading F (N)current I (A)

What the slope and the intercept mean

A wire sits on a balance. The magnetic force pushes down. The balance reads that force plus the weight. The graph plots reading F against current I.

  • F = I L B + mg
  • Slope = L B, because I is on the horizontal axis.
  • Intercept = mg. Gravity pulls even when I = 0.

So B = slope ÷ L and m = intercept ÷ g. To predict a reading, add mg.

Givens: two points on the line are P (0.80 A, 0.530 N) and Q (4.00 A, 0.786 N). The length of wire in the field is 0.120 m. Question: find the field strength B, and the mass of the wire and supports.

01234560.00.20.40.60.81.0scale reading F (N)current I (A)PQ

Field strength and mass from two points

Use two points on the line: P at 0.80 A and Q at 4.00 A. The wire in the field is 0.120 m. Find B and m.

  1. Slope = rise ÷ run, with units.
  2. Field: slope = L B, so B = slope ÷ L.
  3. Intercept: use one point and the slope.
  4. Mass: intercept = mg, so m = intercept ÷ g.

Check: kilograms and tesla. The reading at zero current is below the reading at P.

Diploma: show the slope and intercept steps, with units.

Starting point if needed

The slope is LB and the vertical intercept is mg.

Compare after your attempt

Slope = (0.786 − 0.530)/(4.00 − 0.80) = 0.0800 N per A = LB, so B = 0.0800/0.120 = 0.667 T.

Intercept = 0.530 − (0.0800)(0.80) = 0.466 N = mg, so m = 0.466/9.81 = 4.75 × 10⁻² kg.

Two wires, two forces

Watch this part in the video

On a small screen, scroll sideways to read the labels.

In B10, a current made a magnetic field. So two wires push on each other.
Givens: wire A and wire B are long, straight, parallel and close together. Each carries conventional current up the page.

AB

Parallel currents attract

Each wire makes a field, and sits in the other’s field. Use two hand rules: field first, then force.

  1. Field of A: thumb up along its current, fingers curl round. At B the field is into the page.
  2. Force on B: fingers into the page, thumb up. The palm faces left, toward A.

The force on A is to the right. The forces are equal in size and opposite in direction. Same-direction currents attract. Opposite-direction currents repel.

Diploma: do two steps, the field first and then the force.

Givens: wire A carries conventional current up the page and wire B, to its right, carries conventional current down the page. Question: do the wires attract or repel, and which way is the force on B?

AB

Opposite currents

Now B has current down the page. A still has current up. The field of A at B has not changed.

  1. Field of A at B: into the page, as before.
  2. Force on B: fingers into the page, thumb down this time.
  3. Compare with the last case.
  4. Decide: attract or repel? Say which way the force on B points.
Starting point if needed

The field of A at B is the same as before. What did the reversal change?

Compare after your attempt

The field of A at B is into the page. B’s current is down, so the thumb points down and the fingers point into the page: the palm faces right.

The force on B is to the right, away from A, so currents in opposite directions repel.

How a motor’s coil turns

On a small screen, scroll sideways to read the labels.

On slide 1, a wire in a field felt a force. A motor uses that force to turn a loop.
Givens: a rectangular loop of wire sits between a north pole on the left and a south pole on the right, so the field points to the right. The loop can spin on a vertical axle. A battery sends conventional current up the left side of the loop and down the right side.

NSBaxlesplit ring (commutator)IIFF

Two sides, two opposite forces

A motor is a loop of wire in a magnetic field. Each side of the loop is a wire in a field.

  1. On the left side the current is up. The force is into the page.
  2. On the right side the current is down. The force is out of the page.
  3. The forces are opposite, so the loop turns.
  4. Every half turn, the split ring reverses the current. The loop keeps turning one way.

The split ring is called a commutator. More current or more turns gives a larger force.

Givens: the same loop and magnets, with the field pointing to the right. The battery wires are swapped, so the conventional current now goes down the left side of the loop and up the right side. Question: (a) which way is the force on the left side, and on the right side? (b) Does the loop turn the same way as before, or the opposite way?

NSBaxlesplit ring (commutator)II

Swap the battery wires

Only the current has changed. It now goes down the left side and up the right side.

  1. Left side: fingers right, thumb down. Where does the palm face?
  2. Right side: fingers right, thumb up. Where does the palm face?
  3. Compare with the first picture. Which way does the loop turn now?

Diploma: reverse the current or the field, and the force reverses.

Starting point if needed

Only the current has changed. Reversing the current reverses the force on each side.

Compare after your attempt

(a) Left side: fingers right, thumb down, so the palm faces out of the page. Right side: thumb up, so the palm faces into the page.

(b) Both forces have reversed, so the loop turns the opposite way. Reversing the current reverses a motor.

Practice question

A wire carries conventional current to the right through a magnetic field that points up the page. Is the magnetic force on the wire into the page or out of the page?

Hint

Fingers along the field, thumb along the current. Read the palm.

Compare after your attempt

Fingers up the page (along the field), thumb right (along the conventional current), and the palm faces out of the page. The force on the wire is out of the page.

Practice question

A 0.250 m length of wire carries 5.0 A at right angles to a magnetic field of 0.80 T. Find the magnetic force.

Hint

The wire is at right angles to the field, so use F = ILB.

Compare after your attempt

F = ILB = (5.0)(0.250)(0.80) = 1.0 N.

Practice question

12 C of charge pass through a wire in 3.0 s. A 0.100 m length of the wire is at right angles to a field of 0.50 T. Find the force on it.

Hint

Find the current from I = q ÷ t first.

Compare after your attempt

I = q/t = 12/3.0 = 4.0 A, so F = ILB = (4.0)(0.100)(0.50) = 0.20 N.

Practice question

A wire of mass 2.4 g has 0.100 m of its length at right angles to a field of 0.250 T. What current makes the magnetic force exactly balance gravity?

Hint

The forces balance: ILB = mg. Change grams to kilograms.

Compare after your attempt

ILB = mg, so I = mg/(LB) = (2.4 × 10⁻³)(9.81)/[(0.100)(0.250)] = 0.942 A.

Practice question

A graph of scale reading against current for a wire in a field gives the line F = 0.0800 I + 0.466 (F in newtons, I in amperes). What should the scale read when the current is 5.5 A, and why can you not use F = ILB alone?

Hint

Use the whole line: slope times current, plus the intercept.

Compare after your attempt

F = 0.0800(5.5) + 0.466 = 0.906 N. F = ILB is only the magnetic force; the scale also reads the weight of the wire and supports, which is the intercept.

Practice question

A wire of mass 1.40 g has 0.0900 m of its length in a field of 0.0500 T. A current of 4.00 A flows so that the magnetic force points down. Find the net force on the wire, with its direction.

Hint

Both forces point down, so add them.

Compare after your attempt

Fm = ILB = (4.00)(0.0900)(0.0500) = 0.01800 N down and Fg = mg = 0.01373 N down, so they add: Fnet = 3.17 × 10⁻² N, down.

Practice question

Two parallel wires carry currents in the same direction. Do they attract or repel, and why?

Hint

Find the field of one wire at the other wire. Then find the force on the second wire.

Compare after your attempt

They attract. Say both currents are up. The field of wire A at B is into the page, and the field of wire B at A is out of the page. The right hand (fingers along the field, thumb up) gives a force on B toward A and a force on A toward B.

Challenge question

Challenge: A wire of mass 3.00 g has 0.150 m of its length in a horizontal magnetic field of 0.200 T, at right angles to the field. The magnetic force on the wire points up. What current makes the wire accelerate upward at 2.00 m/s²? Use g = 9.81 N/kg.

Hint

The wire is not at rest, so the forces do not balance. Write ILB − mg = ma.

Compare after your attempt

Two forces act: ILB up and mg down. Newton’s second law: ILB − mg = ma, so ILB = m(g + a). I = m(g + a) ÷ (LB) = (3.00 × 10⁻³)(9.81 + 2.00) ÷ [(0.150)(0.200)] = 1.18 A. Check: this is more than the 0.981 A needed just to hold the wire still.