A4 · Ionic lattices and the properties they explain · Completed notes
Goals: Describe an ionic solid as a crystal lattice of ions. Explain why ionic compounds are hard, brittle and hard to melt, why many dissolve in water, and when they conduct electricity. Compare the melting points of two ionic compounds from the charges and sizes of their ions.
These are the completed notes. The blanks are filled in and each question is worked.
Slide 1 of 6 · An ionic solid is a lattice
In lesson A3 you drew one K⁺ ion and one Br⁻ ion. A real crystal holds billions of each. Today you see how they fit together.
Key ideas
Ions pack together in a repeating pattern called a crystal lattice.
Each positive ion is surrounded by negative ions.
An ionic solid has no separate molecules.
So an ionic formula is a ratio.
Example
What does the formula CaF₂ tell you about a crystal of calcium fluoride?
- The formula is a ratio.
- The crystal has two fluoride ions for every calcium ion.
- It is not one molecule.
Try it
What does the formula KBr tell you about a crystal of potassium bromide?
- The formula is a ratio.
- The crystal has one potassium ion for every bromide ion.
- It is not one molecule.
Slide 2 of 6 · Hard, brittle and hard to melt
On the last slide, every ion was pulled by all its neighbours. Those pulls explain what you see when you heat or hit an ionic solid.
Key ideas
An ionic solid is hard. Its pulls are strong and act in every direction.
It has a high melting point. Melting means the ions break free of the pattern.
It is brittle. A hard hit makes it shatter.
A hit slides one layer along. Then like charges repel and the crystal splits.
Example
After a layer slides, why do the two layers push apart?
- Ions with the same charge are now side by side.
- Like charges repel.
- So the layers push apart.
Try it
Why does an ionic solid need a high temperature to melt?
- Each ion is held by strong pulls from all its neighbours.
- Melting means the ions break free.
- That takes a lot of energy.
Slide 3 of 6 · Dissolving and conducting
So far the lattice stayed whole. Water can take a lattice apart. Then the ions can move, and the compound behaves in a new way.
Key ideas
Many ionic compounds dissolve in water. Water pulls the ions out of the lattice.
A substance conducts electricity when charged particles can move through it.
In the solid, the ions are fixed. The solid does not conduct.
A solution that conducts is called an electrolyte.
Example
Solid potassium bromide does not conduct, but melted potassium bromide does. Why?
- In the solid, the ions are fixed in the lattice.
- In the liquid, the ions can move.
- Moving ions carry the current.
Try it
Will potassium bromide dissolved in water conduct? Say why.
- Yes.
- Water pulls the ions out of the lattice.
- The separate ions are free to move, so the solution conducts.
Slide 4 of 6 · Comparing melting points
On slide 2, potassium bromide melted at 734 °C. Other ionic compounds melt higher or lower. Two things about the ions decide it.
Key ideas
Potassium bromide melts at 734 °C. Potassium fluoride melts at 858 °C.
Bigger ions sit farther apart, so they pull less strongly.
So smaller ions give a higher melting point.
Bigger charges pull much more strongly, so they give a higher melting point.
Example
Potassium iodide has a bigger negative ion than potassium bromide. Will it melt above or below 734 °C?
- The charges are the same, so compare the sizes.
- Bigger ions are farther apart and pull less strongly.
- Potassium iodide melts below 734 °C.
Try it
Which melts higher, rubidium chloride (ions 1+ and 1−) or strontium sulfide (ions 2+ and 2−)?
- The charges differ, so compare the charges.
- Bigger charges pull more strongly.
- Strontium sulfide melts higher.
Slide 5 of 6 · Method: how to compare the melting points of two ionic compounds
You just compared two pairs of compounds. Each time you looked at the charges and the sizes. Here that is as four steps.
Key ideas
Step 1: write the ions of each compound, with charges.
Step 2: compare the charges. Bigger charges melt higher.
Step 3: compare the sizes. Smaller ions melt higher.
Step 4: state which melts higher, and why.
Example
Use the four steps to decide which melts higher, sodium fluoride or sodium iodide.
- Step 1: NaF has Na⁺ and F⁻. NaI has Na⁺ and I⁻.
- Step 2: the charges are the same, 1+ and 1−.
- Step 3: fluoride is smaller than iodide.
- Step 4: sodium fluoride melts higher, because its ions are closer and pull harder.
Try it
Use the four steps to decide which melts higher, calcium sulfide or potassium chloride.
- Step 1: CaS has Ca²⁺ and S²⁻. KCl has K⁺ and Cl⁻.
- Step 2: the charges in CaS are bigger, 2+ and 2−.
- Step 3 is not needed, because the charges decide.
- Step 4: calcium sulfide melts higher, because bigger charges pull harder.
Slide 6 of 6 · Ionic compounds around us
In this lesson, ionic compounds were hard, brittle and hard to melt. Many also dissolved in water. People choose them for jobs that suit those properties.
Key ideas
Calcium chloride melts ice on winter roads.
Potassium chloride is a fertilizer.
Sodium fluoride in toothpaste hardens teeth.
Each ionic compound is chosen for its properties.
Example
Calcium chloride is used to melt road ice. Which property makes that possible?
- It dissolves in water.
- Its separate ions lower the temperature at which water freezes.
Try it
Name one ionic compound you use at home, and say what it is used for.
- One answer is sodium fluoride.
- It is in toothpaste and hardens teeth.
- Calcium carbonate in antacid tablets is another answer.